Asynchronous operation for compatibility with industry-
standard 512K x 8 SRAMs
CMOS compatible inputs and output levels, three-state
bidirectional data bus
- I/O Voltage 3.3 volts, 1.8 volt core
Radiation performance
- Intrinsic total-dose: 300 Krad(Si)
- SEL Immune >100 MeV-cm
2
/mg
- LET
th
(0.25): 53.0 MeV-cm
2
/mg
- Memory Cell Saturated Cross Section 1.67E-7cm
2
/bit
- Neutron Fluence: 3.0E14n/cm
2
- Dose Rate
- Upset 1.0E9 rad(Si)/sec
- Latchup 1.0E11 rad(Si)/sec
Packaging options:
- 68-lead ceramic quad flatpack (20.238 grams with lead
frame)
Standard Microcircuit Drawing 5962-04227
- QML compliant part
INTRODUCTION
The UT8CR512K32 is a high-performance CMOS static RAM
multi-chip module (MCM), organized as four individual
524,288 words by 8 bit SRAMs with common output enable.
Easy memory expansion is provided by active LOW chip
enables (EN), an active LOW output enable (G), and three-state
drivers. This device has a power-down feature that reduces
power consumption by more than 90% when deselected.
Writing to each memory is accomplished by taking the
corresponding chip enable (En) input LOW and write enable
(Wn) input LOW. Data on the I/O pins is then written into the
location specified on the address pins (A
0
through A
18
). Reading
from the device is accomplished by taking the chip enable (En)
and output enable (G) LOW while forcing write enable (Wn)
HIGH. Under these conditions, the contents of the memory
location specified by the address pins will appear on the I/O pins.
The input/output pins are placed in a high impedance state when
the device is deselected (En HIGH), the outputs are disabled (G
HIGH), or during a write operation (En LOW and Wn LOW).
Perform 8, 16, 24 or 32 bit accesses by making Wn along with
En a common input to any combination of the discrete memory
die.
W2
E1
W1
W0
E0
E3
A(18:0)
G
W3
E2
512K x 8
512K x 8
512K x 8
512K x 8
DQ(31:24)
or
DQ3(7:0)
DQ(23:16)
or
DQ2(7:0)
DQ(15:8)
or
DQ1(7:0)
DQ(7:0)
or
DQ0(7:0)
Figure 1. UT8CR512K32 SRAM Block Diagram
1
V
DD1
A0
A1
A2
A3
A4
A5
E2
V
SS
E3
W0
A6
A7
A8
A9
A10
V
DD2
DEVICE OPERATION
DQ0(2)
DQ1(2)
DQ2(2)
DQ3(2)
DQ4(2)
DQ5(2)
DQ6(2)
DQ7(2)
V
SS
DQ0(3)
DQ1(3)
DQ2(3)
DQ3(3)
DQ4(3)
DQ5(3)
DQ6(3)
DQ7(3)
DQ0(0)
DQ1(0)
DQ2(0)
DQ3(0)
DQ4(0)
DQ5(0)
DQ6(0)
DQ7(0)
V
SS
DQ0(1)
DQ1(1)
DQ2(1)
DQ3(1)
DQ4(1)
DQ5(1)
DQ6(1)
DQ7(1)
68 67 66 65 64 63 62 61 60 59 58 57 56 555453 52
1
51
2
50
3
49
4
48
5
47
Top View
6
46
7
45
8
44
9
43
10
42
11
41
12
40
13
39
14
38
15
37
16
36
17
35
1819 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
V
DD2
A11
A12
A13
A14
A15
A16
E0
G
E1
A17
W1
W2
W3
A18
V
DD1
V
SS
Each die in the UT8CR512K32 has three control inputs called
Enable (En), Write Enable (Wn), and Output Enable (G); 19
address inputs, A(18:0); and eight bidirectional data lines,
DQ(7:0). The device enable (En) controls device selection,
active, and standby modes. Asserting En enables the device,
causes I
DD
to rise to its active value, and decodes the 19 address
inputs to each memory die by selecting the 2,048,000 byte of
memory. Wn controls read and write operations. During a read
cycle, G must be asserted to enable the outputs.
Table 1. Device Operation Truth Table
G
X
X
1
0
WN
X
0
1
1
EN
1
0
0
0
I/O Mode
3-state
Data in
3-state
Data out
Mode
Standby
Write
Read
2
Read
Figure 2. 17ns SRAM Pinout 68)
PIN NAMES
A(18:0)
DQ(7:0)
EN
W
G
V
DD1
V
DD2
V
SS
Address
Data Input/Output
Enable
Write Enable
Output Enable
Power (1.8V)
Power (3.3V)
Ground
Notes:
1. “X” is defined as a “don’t care” condition.
2. Device active; outputs disabled.
READ CYCLE
A combination of Wn greater than V
IH
(min) with En and G less
than V
IL
(max) defines a read cycle. Read access time is
measured from the latter of device enable, output enable, or valid
address to valid data output.
SRAM read Cycle 1, the Address Access is initiated by a change
in address inputs while the chip is enabled with G asserted and
Wn deasserted. Valid data appears on data outputs DQn(7:0)
after the specified t
AVQV
is satisfied. Outputs remain active
throughout the entire cycle. As long as device enable and output
enable are active, the address inputs may change at a rate equal
to the minimum read cycle time (t
AVAV
).
SRAM read Cycle 2, the Chip Enable-controlled Access is
initiated by En going active while G remains asserted, Wn
remains deasserted, and the addresses remain stable for the
entire cycle. After the specified t
ETQV
is satisfied, the eight-bit
word addressed by A(18:0) is accessed and appears at the data
outputs DQn(7:0).
SRAM read Cycle 3, the Output Enable-controlled Access is
initiated by G going active while En is asserted, Wn is
deasserted, and the addresses are stable. Read access time is
t
GLQV
unless t
AVQV
or t
ETQV
have not been satisfied.
2
WRITE CYCLE
A combination of Wn less than V
IL
(max) and En less than
V
IL
(max) defines a write cycle. The state of G is a “don’t care”
for a write cycle. The outputs are placed in the high-impedance
state when either G is greater than V
IH
(min), or when Wn is less
than V
IL
(max).
Write Cycle 1, the Write Enable-controlled Access is defined
by a write terminated by Wn going high, with En still active.
The write pulse width is defined by t
WLWH
when the write is
initiated by Wn, and by t
ETWH
when the write is initiated by En.
Unless the outputs have been previously placed in the high-
impedance state by G, the user must wait t
WLQZ
before applying
data to the eight bidirectional pins DQn(7:0) to avoid bus
contention.
Write Cycle 2, the Chip Enable-controlled Access is defined by
a write terminated by the former of En or Wn going inactive.
The write pulse width is defined by t
WLEF
when the write is
initiated by Wn, and by t
ETEF
when the write is initiated by the
En going active. For the Wn initiated write, unless the outputs
have been previously placed in the high-impedance state by G,
the user must wait t
WLQZ
before applying data to the eight
bidirectional pins DQn (7:0) to avoid bus contention.
RADIATION HARDNESS
The UT8CR512K32 SRAM incorporates special design and
layout features which allows operation in a limited radiation
environment.
Table 2. Radiation Hardness
Design Specifications
1
Total Dose
Heavy Ion
Error Rate
2
300K
8.9x10
-10
rad(Si)
Errors/Bit-Day
Notes:
1. The SRAM is immune to latchup to particles >100MeV-cm
2
/mg.
2. 10% worst case particle environment, Geosynchronous orbit, 100 mils of
Aluminum.
Supply Sequencing
No supply voltage sequencing is required between V
DD1
and
V
DD2
.
3
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD1
V
DD2
V
I/O
T
STG
P
D
T
J
Θ
JC
I
I
PARAMETER
DC supply voltage
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
2
Thermal resistance, junction-to-case
3
DC input current
LIMITS
-0.3 to 2.0V
-0.3 to 3.8V
-0.3 to 3.8V
-65 to +150°C
1.2W
+150°C
5°C/W
±
5 mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at
these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
2. Maximum junction temperature may be increased to +175°C during burn-in and steady-static life.
3. Test per MIL-STD-883, Method 1012.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD1
V
DD2
T
C
V
IN
PARAMETER
Positive supply voltage
Positive supply voltage
Case temperature range
DC input voltage
LIMITS
1.7 to 1.9V
3.0 to 3.6V
(C) Screening: -55 to +125°C
(W) Screening: -40 to +125°C
0V to V
DD2
4
DC ELECTRICAL CHARACTERISTICS (Pre and Post-Radiation)*
(-55°C to +125°C for (C) screening and -40°C to 125°C for (W) screening)
SYMBOL
V
IH
V
IL
V
OL1
V
OH1
C
IN1
C
IO1
I
IN
I
OZ
PARAMETER
High-level input voltage
Low-level input voltage
Low-level output voltage
High-level output voltage
Input capacitance
Bidirectional I/O capacitance
Input leakage current
Three-state output leakage
current
Short-circuit output current
I
OL
= 8mA,V
DD2
=V
DD2
(min)
I
OH
= -4mA,V
DD2
=V
DD2
(min)
ƒ
= 1MHz @ 0V
ƒ
= 1MHz @ 0V
V
IN
= V
DD2
and V
SS
V
O
= V
DD2
and V
SS,
V
DD2
= V
DD2
(max)
G = V
DD2
(max)
V
DD2
= V
DD2
(max), V
O
= V
DD2
V
DD2
= V
DD2
(max), V
O
= V
SS
Inputs : V
IL
= V
SS
+ 0.2V
V
IH
= V
DD2
- 0.2V, I
OUT
= 0
V
DD1
= V
DD1
(max), V
DD2
= V
DD2
(max)
Inputs : V
IL
= V
SS
+ 0.2V,
V
IH
= V
DD2
- 0.2V, I
OUT
= 0
V
DD1
= V
DD1
(max), V
DD2
= V
DD2
(max)
Inputs : V
IL
= V
SS
+ 0.2V
V
IH
= V
DD2
- 0.2V, I
OUT
= 0
V
DD1
= V
DD1
(max), V
DD2
= V
DD2
(max)
Inputs : V
IL
= V
SS
+ 0.2V,
V
IH
= V
DD2
- 0.2V, I
OUT
= 0
V
DD1
= V
DD1
(max), V
DD2
= V
DD2
(max)
CMOS inputs , I
OUT
= 0
EN = V
DD2
-0.2
V
DD1
= V
DD1
(max), V
DD2
= V
DD2
(max)
CMOS inputs , I
OUT
= 0
EN = V
DD2
- 0.2
V
DD1
= V
DD1
(max), V
DD2
= V
DD2
(max)
93
mA
-2
-2
.8*V
DD2
12
12
2
2
CONDITION
MIN
.7*V
DD2
.3*V
DD2
.2*V
DD2
MAX
UNIT
V
V
V
V
pF
pF
µA
µA
I
OS2, 3
-100
+100
mA
I
DD1
(OP
1
)
Supply current operating
@ 1MHz
45
mA
I
DD1
(OP
2
)
Supply current operating
@66MHz
I
DD2
(OP
1
)
Supply current operating
@ 1MHz
243
µA
I
DD2
(OP
2
)
Supply current operating
@66MHz
12
mA
I
DD1
(SB)
4
I
DD2
(SB)
4
I
DD1
(SB)
4
I
DD2
(SB)
4
Supply current standby @
0Hz
38
100
38
100
mΑ
µA
mΑ
µA
Supply current standby
A(18:0) @ 66MHz
Notes:
* Post-radiation performance guaranteed at 25°C per MIL-STD-883 Method 1019 at 1.0E5 rad(Si).
1. Measured only for initial qualification and after process or design changes that could affect input/output capacitance.
2. Supplied as a design limit but not guaranteed or tested.
3. Not more than one output may be shorted at a time for maximum duration of one second.
This is the stdarg.h of KEIL 4This is the stdarg.h of IAR6.3This is the prototype definition of va_arg(ap,t) of IAR. Now I am porting a TFT program to Freescale K60, so I am using IAR6.3 compiler. Now...
China Unicom's WCDMA is now available, great news! Let me tell you about my experience with WCDMA when I went to Australia this year, and I'll post a few pictures. Several of my classmates are studyin...
I used 373 and 138 to expand the IO port of 51 MCU. The data port of 1602 is connected to P0 RS/RW/E and connected to the Q terminal of 373. Is this OK? How to realize the operation sequence?...
This is a classic book written by an American, a world-class switching power supply expert! It is easy to understand and a must-read for power supply designers! However, there is only an electronic ve...
Emergency hand-held lamps powered by 6V maintenance-free batteries are widely used in rural areas. The charger used is a transformer step-down and single diode half-wave rectifier, and the charging...[Details]
Sailing is gaining more and more attention. How to use modern technology to assist training and improve competition results is particularly important. Considering the real-time data collection in t...[Details]
In the previous series, we have listed some basic knowledge of C language in Tables 1 to 3. We hope that beginners can strengthen their memory of the above tables and gradually learn to use them wh...[Details]
1. With the development of modern industry and the continuous improvement of automation, some medium and large control systems have been greatly facilitated, which not only makes control easier, bu...[Details]
1. Introduction to CIF Board
Fieldbus integration based on PC system
Whether it is a master or a slave, fieldbus has won unanimous praise in the field of PC-based automation. For more...[Details]
The potentiometer is an adjustable electronic component. The main functions of the potentiometer in the circuit are as follows:
1. Used as a voltage divider
A potentiometer is a continuou...[Details]
With the advocacy and implementation of the government's Safe City Plan, the security market has increasingly higher requirements for the clarity of surveillance images. Imagine that after a case o...[Details]
introduction
MEMS is a high-tech that has flourished on the basis of integrated circuit production technology and dedicated micro-electromechanical processing methods. Pressure sensors develop...[Details]
1. Proposal of
reconfigurable
measurement and control system
The measurement and control system generally refers to a system based on
computers
to realize data acquisition a...[Details]
A stepper motor is an electromagnetic mechanical device that converts an electrical pulse signal into an angular displacement or a linear displacement. The stability and reliability of a stepper mo...[Details]
1 Embedded Systems
Embedded System refers to a collection of computer hardware and software with specific functions or purposes, which is divided into embedded software system and embe...[Details]
Portable power applications are broad and varied. Products range from wireless sensor nodes with average power consumption of only a few microwatts to in-vehicle medical or data acquisition systems...[Details]
The overall operating performance of an electric car depends first on its battery system and motor drive system. The drive system of an electric car is generally composed of three main parts: a con...[Details]
(1) Open circuit voltage of the battery
(2) Internal resistance of the battery
(3) Battery operating voltage
(4) Charging voltage
Charging voltage refers to the voltage applied ...[Details]
Since the implementation of the self-weight toll collection system, the highway administration has not only high requirements for the vehicle axle recognition rate, but also requires a long service li...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
