EEWORLDEEWORLDEEWORLD

Part Number

Search

G12JPF

Description
TOGGLE SWITCH
Categoryunclassified   
File Size120KB,4 Pages
ManufacturerNKK
Websitehttps://www.nkkswitches.com.cn
Download Datasheet Parametric Compare View All

G12JPF Online Shopping

Suppliers Part Number Price MOQ In stock  
G12JPF - - View Buy Now

G12JPF Overview

TOGGLE SWITCH

G12JPF Parametric

Parameter NameAttribute value
stateACTIVE
Manufacturer SeriesG
Switch typeTOGGLE SWITCH
Series G
Toggles
Fully Illuminated Ultra-Miniature Toggles
A
Rockers
General
Specifications
Electrical Capacity (Resistive Load)
Logic Level:
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Programmable Illuminated PB
Pushbuttons
Other Ratings
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Keylocks
Nominal Operating Force:
Angle of Throw:
80 milliohms maximum
500 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
100,000 operations minimum
100,000 operations minimum
10,000 operations minimum @ 0.1A @ 28V AC/DC
1.30N
28°
Materials & Finishes
Rotaries
Actuator:
Case:
Sealing Rings:
Movable Contacts:
Stationary Contacts:
Base:
Power Terminals:
Lamp Terminals:
Polyamide
Glass fiber reinforced polyamide
Nitrile butadiene rubber
Phosphor bronze with gold plating
Phosphor bronze with gold plating
Glass fiber reinforced polyamide
Phosphor bronze with gold plating
Phosphor bronze with gold plating
Tactiles
Slides
Environmental Data
Operating Temperature Range:
Humidity:
Vibration:
Shock:
–25°C through +55°C (–13°F through +131°F)
90 ~ 95% humidity for 240 hours @ 40°C (104°F)
10 ~ 500Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range
& returning in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
2
) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Tilt
Touch
PCB Processing
Soldering:
Cleaning:
Wave Soldering recommended. See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
Automated cleaning. See Cleaning specifications in Supplement section.
Indicators
Standards & Certifications
Supplement
Accessories
The G Series toggles have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
A38
www.nkk.com

G12JPF Related Products

G12JPF G13JHC G13JHD G13JHF G13JPC G13JPD G13JVC G13JVD G13JVF
Description TOGGLE SWITCH TOGGLE SWITCH TOGGLE SWITCH TOGGLE SWITCH TOGGLE SWITCH TOGGLE SWITCH TOGGLE SWITCH TOGGLE SWITCH TOGGLE SWITCH
state ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE
Manufacturer Series G G G G G G G G G
Switch type TOGGLE SWITCH TOGGLE SWITCH TOGGLE SWITCH TOGGLE SWITCH TOGGLE SWITCH TOGGLE SWITCH TOGGLE SWITCH TOGGLE SWITCH TOGGLE SWITCH
How to operate each IO port when cascading two PCA9539 in STM32?
As shown above, this is my first time using this chip. The chip manual says that A0 and A1 are used to control the chip address. In the left picture, A0 is low level, and in the right picture, A0 is h...
大时代阿达 stm32/stm8
After reading the exchange notice of Chip Coin, I feel that Brother Wateras1 has become more high-end and classy.
Let's take a look at the pictures! :lol Brother Nan sent it to me personally! [[i] This post was last edited by wstt on 2013-8-7 00:00[/i]]...
wstt Talking
L298N common ground problem
I use L298N integrated board to drive 12V motor. I use 12V power supply to power the microcontroller through 7805 voltage regulator. Now the control terminal GND and output terminal GND of L298N are c...
马铃薯疯子 51mcu
Why is there such a big difference in STM8S10ms timing?
void T2_Init(void){TIM2_TimeBaseInit(TIM2_PRESCALER_256, 0xffff-625+1);TIM2_ITConfig(TIM2_IT_UPDATE, ENABLE);enableInterrupts();TIM2_Cmd(ENABLE);}Using HSI, 16MHz, no frequency division, the above tim...
barowind stm32/stm8
I designed my own power supply, please give me some advice
I designed one when I was free, but it can only achieve constant voltage, and I haven't done cross-current yet. The basic principle is that the microcontroller detects the output voltage, and then use...
MrKingMCU Power technology
Switching power supply with extremely wide input voltage range
Some portable electronic devices want their power adapters to be suitable for both AC mains with a global voltage range and 12V and 24VDC batteries in cars. Usually the most convenient solution is to ...
KMO Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2612  2086  1117  713  888  53  43  23  15  18 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号