[i=s]This post was last edited by liwei198905 on 2016-9-23 00:47[/i] In the last review, the basic functions of 279FC were described in detail, mainly including the measurement of resistance, voltage ...
This article introduces how to design a web application on the Alibaba Cloud IoT Studio platform to display temperature, humidity, and noise levels using dashboards and line charts. Design a button an...
[align=left][font=微软雅黑][size=3]1. Loop Stability Evaluation Index [/size][/font][/align][align=left][font=微软雅黑][size=3]The indicators for measuring the stability of a switching power supply are phase ...
6.4 Capture Compare Module This is the official introduction to the important functions of TA based on the above introduction. First, let's look at a register TACCTL0-TACCTL6: (The most complex regist...
I use CJ2310 MOS tube, power supply voltage DC24VQuestion: As shown in the figure below, according to my understanding, the voltage of the linear resistor should be 24V, but it is only 11V. The GS vol...
International Solar Photovoltaic Network News: Chinese inverter company Sungrow announced that it will build a 3GW photovoltaic inverter manufacturing plant in Bangalore, the capital of Karnataka, ...[Details]
In the
AI
boom, the most talked about is
neural network
. However,
AI
is much more than that. Let's learn about the relevant content with the network communication editor.
...[Details]
After searching a lot of information, I finally understood the time base timer. I did not use any library functions but operated the registers directly. The following introduces the systick in STM32...[Details]
In the previous article, I wrote a simple GPIO running light test, which looked a bit monotonous. I was used to serial port debugging. If there was no serial port on the board, I had to find another ...[Details]
The trade war between China and the United States has become the focus. The United States has begun to play the ban card against Chinese technology companies. The ZTE incident shows that if the ban...[Details]
In 1952, Bell Labs built a 6-foot-tall automatic number recognition machine called "Audrey", which could recognize the pronunciation of the numbers 0 to 9 with an accuracy of more than 90%. And its...[Details]
STM32 uses FSMC to read and write CPLD programs. CPLD is hung on the address line and data line of STM32. CPLD is regarded as an off-chip RAM for reading and writing. On the board I made, CPLD is hun...[Details]
As the weather gets colder, the way the north and south spend the winter has become a hot topic and people talk about it. Although the north is particularly cold, because there is heating, it can s...[Details]
From the functional classification, it can be divided into: 1. Active control ADAS: ACC/AEB/LKS, etc. 2. Warning ADAS: FCW/LDW/PCW, etc. 3. Other auxiliary ADAS: BSD/ADB/panora...[Details]
Use the STM32 timer input capture module to control 3-way ultrasonic sensors. The ultrasonic sensor used this time is the common HC-SR04, which is often used in the obstacle avoidance system of smal...[Details]
The pins of stm32 have two uses: GPIO (general purpose io) and AFIO (alternate function io) For some pins (depending on the chip), neither of these two uses exists. For example, in 64-pin products, O...[Details]
When STM32 uses JTMS (PA13) and JTCK (PA14) as normal I/O ports, add the following code before initialization (the order cannot be reversed): RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE); G...[Details]
I have encountered many problems when tinkering with LD driver recently. I will record them one by one below. Otherwise, who will remember who in five hundred years? 1. Configuration issues of multi-...[Details]
ADC: 1. The ADC module inside STM32 has three ADC1, ADC2, and ADC3, which are independent of each other, so synchronous sampling can be performed. 2ADC input clock must not exceed 14MHz, it is genera...[Details]
Test/Measurement
京公网安备 11010802033920号
EEWORLD
