Figures 1 and 2 are photographs of digitized waveforms showing the typical clamping action of a 16A module. A 12 Ohm resistor is used to repre-
sent a 10A equipment load. The load is then subjected to the ANSI/IEEE C62.41 Catagory CI test conditions (6000V/3000A). These photographes
contrast the effect on equipment with and without the protector.
05016.R6 3/11
Page 1
www.protekdevices.com
05016
Only One Name Means ProTek’Tion™
587B051 - 587B301
tyPical Device chaRacteRistics
MaXiMuM Ratings
@ 25°c unless otherwise specified
PaRaMeteR
Operating Line Voltage: +10%
Line Current: 587B051/587B151/587B201/587B301
Peak Transient Voltage
Peak Transient Current
Current Leakage @ 130 Volts AC: Line-to-Neutral & Neutral-to-Ground
Operating Temperature - Note 1
Storage Temperature - Note 1
1. Measured at the center of the mounting surface.
syMBol
V
O
-
-
-
-
T
A
T
STG
value
130
5/15/20/30
6000
3000
1 & 0.5
-40 to 85
-40 to 85
units
Volts AC
Amps
Volts
Amps
mA
°C
°C
notes
electRical chaRacteRistics
@ 25°c unless otherwise specified
PRotection
MoDe
(note 1)
MaXiMuM
claMPing voltage
(note 2)
volts
Line to Neutral
Line to Neutral
Neutral to Ground
Neutral to Ground
notes
295
350
500
650
oPen ciRcuit
voltage
(note 2)
@1.2/50µs
volts
1000
6000
1000
6000
shoRt ciRcuit
cuRRent
(note 2)
@ 8/20µs
aMPs
500
3000
500
3000
1. Differential Mode Protection: Line to Neutral. Common Mode Protection: Neutral to Ground.
2. Test condition responses to transient voltages.
FilteR chaRacteRistics
(noise attenuation db)
Frequency (MHz)
Common Mode Attenuation
Differential Mode Attenuation
0.15
10
30
0.5
25
55
1.0
35
55
5.0
55
55
10
50
50
30
40
45
05016.R6 3/11
Page 2
www.protekdevices.com
05016
Only One Name Means ProTek’Tion™
587B051 - 587B301
tyPical Device chaRacteRistics
aRRestoR DeFinitions
Clamping Voltage: The clamping voltage of an arrester is the voltage that appears across its terminals during conduction of a transient current.
Standard Wave Form: The waveform of a surge current or voltage is designated by a combination of two numbers. The first number is for the time of the wave front
expressed in microseconds from zero to the peak of the wave. The second number is for the time of the wavetail also expressed in microseconds from zero to the
instant that the wavetail reaches one half of the crest or peak value, i.e., 8/20 µs waveform.
Transient Current: The transient current of an arrestor is the peak surge current which flows through the arrester when voltage clamping occurs.
oPeRation
For maximum effectiveness, the protector should be installed directly after the AC line on/off switch and fuse. This will protect the electronics from the AC line switch
arcing and the severe transients caused by a fuse clearing.
Some heat is produced when operating at full current load, and heat sinking may be required to maintain case temperature below 85°C. The case temperature is
measured at the center of the mounting surface. The unit should not be mounted to a low combusting temperature material such as wood.
High energy transients will cause a large circulating current in the AC input line (2,500A is possible). To prevent electromagnetic coupling, the AC line on the input side
of the protector must be dressed away from other wiring, magnetic shielding may be required. In addition, the electrical service must be connected to a low imped-
ance earth ground.
05016.R6 3/11
Page 3
www.protekdevices.com
05016
Only One Name Means ProTek’Tion™
587B051 - 587B301
PacKage inFoRMation
outline DiMensions
P/n
587B051
587B151
587B201
587B301
weight
250
500
750
850
inches
a
2.00
3.00
3.00
3.00
MilliMeteRs
e
1.50
1.50
1.50
1.50
B
2.00
2.00
3.00
3.00
c
2.50
3.50
3.50
3.50
D
3.00
4.00
4.00
4.00
F
0.60
0.60
0.60
0.60
g
0.169
0.169
0.169
0.169
a
50.8
76.2
76.2
76.2
B
50.8
50.8
76.2
76.2
c
63.5
89.0
89.0
89.0
D
76.2
102.0
102.0
102.0
e
38.2
38.2
38.2
38.2
F
15.2
15.2
15.2
15.2
g
4.29
4.29
4.29
4.29
D
C
F
E
LINE IN
LINE OUT
DEVICE
MARKING
NEUTRAL
GROUND
B
G
A
oRDeRing inFoRMation
Base PaRt nuMBeR
(xx = voltage)
587Bxxx
MaRKing
Part Number, Date Code, Voltage, Logo, Current Rating, CSA Logo
05016.R6 3/11
Page 4
www.protekdevices.com
05016
Only One Name Means ProTek’Tion™
587B051 - 587B301
coMPany inFoRMation
coMPany PRoFile
ProTek Devices, based in Tempe, Arizona USA, is a manufacturer of Transient Voltage Suppression (TVS) products designed specifically for
the protection of electronic systems from the effects of lightning, Electrostatic Discharge (ESD), Nuclear Electromagnetic Pulse (NEMP), in-
ductive switching and EMI/RFI. With over 25 years of engineering and manufacturing experience, ProTek designs TVS devices that provide
application specific protection solutions for all electronic equipment/systems.
ProTek Devices Analog Products Division, also manufactures analog interface, control, RF and power management products.
SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice.
DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering
and technical assistance. ProTek assumes no responsibility with respect to the selection or specifications of such products. ProTek makes no warranty, representation or guarantee regarding the suitability of
its products for any particular purpose, nor does ProTek assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability without limitation special,
consequential or incidental damages.
LIFE SUPPORT POLICY: ProTek Devices products are not authorized for use in life support systems without written consent from the factory.
PATENT INFORMATION: This device is patented under U.S. Patent No. 4,563,720
When a call comes in, the incoming call view will pop up, and the toolbar will show two menus: answer and ignore. How can I change this menu? For example, change ignore to menu, or add two menu items ...
Zhang Xinfang: Internationally, there are not many IT companies directly involved in the security industry, but many Fortune 500 companies are involved in the security industry. According to my unders...
YS65F805 is an 8-bit MTP CMOS touch microcontroller. It has powerful performance and low power consumption. Standby current: 500nA at 2.5V. Working current: 500uA at 8MHz and 2.5V. 120uA at 31kHz and ...
I want to use USB RNDIS for KITL debugging, but I don't know how to do it. In addition to setting build options and connectivity options, is there any additional work required from the driver code per...
Undoubtedly, the feature of this board is dual-core, and it is not easy to deeply understand how the dual-core works just from the introduction in the user manual. More information and practice are ne...
I just graduated this year and I don't know anything yet. My company wants me to make a device that converts 220v power into 12v and 5v without a transformer. Which senior can teach me how to do this?...
On August 23rd, Geely's subsidiary, Jiyao Tongxing, announced it has the industry's largest advanced production capacity for tandao
batteries
, with eight production bases across China. Jiy...[Details]
Tesla and BYD, vying for dominance in the global electric vehicle market, are reportedly considering adopting Samsung's AMOLED (active-matrix organic light-emitting diode) technology for their next...[Details]
1. Project Overview
1.1 Introduction
Currently, most music files are saved in MP3 format, a lossy audio compression format that cannot perfectly reproduce the original music. With the exp...[Details]
When you are happily watching NBA or football, your wife asks you to turn off the lights in the bedroom. Would you be depressed? Of course, unless you are not afraid of your wife.
Now you are ...[Details]
A vacuum eutectic furnace is a critical piece of equipment used in the manufacturing and processing of various materials, particularly in the fields of microelectronics and nanotechnology. One of t...[Details]
introduction
With the development of digital and network technologies, broadcasting technology has become increasingly diversified, with the most significant trend being the transition from an...[Details]
According to foreign media reports, Nissan Motor has recently reached a cooperation with US battery technology company LiCAP Technologies to jointly promote the research and development of next-gen...[Details]
One of the most core components of electric vehicles is the motor. The power supply provides electrical energy to the motor, which converts this electrical energy into mechanical energy, which in t...[Details]
China, August 21, 2025 – STMicroelectronics (NYSE: STM), a world-leading semiconductor company serving a wide range of electronics applications, has published its IFRS 2025 semi-annual financial re...[Details]
Tools/Materials
Yitong Chuanglian MODBUS to PROFIBUS Gateway YT-PB-03
Siemens s7-300
This article describes how to configure the YT-PB-03 MODBUS to PROFIBUS gat...[Details]
With the support and encouragement of national policies, some Internet car manufacturers have also joined the new energy vehicle manufacturing industry. From the perspective of new car manufacturer...[Details]
Tires are a very important component for cars. They are related to the driving experience of the vehicle. We are almost inseparable from cars in our daily lives. For tires, according to the role of...[Details]
introduction
The rapid adoption of computers has led to a growing number of tasks being performed on them. People from all walks of life, especially programmers and writers, are spending incre...[Details]
The fracture mechanism is stress concentration, which typically occurs at the capacitor lead pins or pad connection points, as shown in the figure. Under vibration, the capacitor lead pins and pad ...[Details]
Batteries are a core component of new energy vehicles, accounting for over 40% of the total cost. This is also the area where automakers are most willing to tamper with costs. Since 2021, domestic ...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
