EEWORLDEEWORLDEEWORLD

Part Number

Search

51720-11507602AALF

Description
Board Connector, Female, Right Angle, Solder Terminal, Locking, Receptacle
CategoryThe connector    The connector   
File Size272KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

51720-11507602AALF Overview

Board Connector, Female, Right Angle, Solder Terminal, Locking, Receptacle

51720-11507602AALF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAmphenol
Reach Compliance Codecompliant
body width0.574 inch
subject depth0.93 inch
body length6.8 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact completed and terminatedTIN OVER NICKEL
Contact point genderFEMALE
Contact materialCOPPER ALLOY
Contact resistance2 mΩ
Contact styleHYBRID
Dielectric withstand voltage2500VDC V
Durability200 Cycles
maximum insertion force.973 N
Insulation resistance10000000000 Ω
insulator materialGLASS FILLED THERMOPLASTIC
Manufacturer's serial number51720
Mixed contactsYES
Installation option 1LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature105 °C
Minimum operating temperature-20 °C
Plating thickness30u inch
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.135 inch
Termination typeSOLDER
Evacuation force-minimum value.17792 N
PDM: Rev:P
STATUS:
Released
Printed: Dec 20, 2010
.
In the second week, when testing the single propeller with the BeagleBone development board chip, I found that it was fake.
The board has been made for a while. I didn't pay much attention to the full performance test on it before. The M3 M4 series is also good at brushless motor projects, so I didn't pay much attention to...
PENGSHIFANG DSP and ARM Processors
ISM330DLC three-axis acceleration + three-axis angular velocity sensor package and code
Data sheet:Code:Package:Official evaluation board gerber file:...
littleshrimp MEMS sensors
Altium Designer operation process and brief introduction
Altium Designer, referred to as AD, is a hardware development software. Let's take AD18 as an example to explain the simple operation process of AD. If you want to use AD to design a board, the most b...
电鱼电子工程师 PCB Design
Commonly used subroutines for single chip microcomputers
[i=s] This post was last edited by paulhyde on 2014-9-15 09:28 [/i] There are many commonly used module programs. I hope it will be helpful to beginners and make it easier to get started~~...
xianghong123 Electronics Design Contest
DAC adjusts the output voltage of DCDC chip
As shown in the figure below, the higher the DAC voltage, the lower the output voltageHowever, actual circuits have found that there is an inflection point. Before the inflection point, this relations...
sfcsdc Analog electronics
What is the principle of this inductor?
Connect one end of each leg and twist the other end together to ground. What is the principle, the effect of hair raising, and how to know the inductance value?...
lhycpqq Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1071  1850  2501  2733  1890  22  38  51  56  39 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号