EEWORLDEEWORLDEEWORLD

Part Number

Search

51740-10409604ALF

Description
Board Connector, 104 Contact(s), Female, Right Angle, Solder Terminal, Locking, Receptacle
CategoryThe connector    The connector   
File Size243KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

51740-10409604ALF Overview

Board Connector, 104 Contact(s), Female, Right Angle, Solder Terminal, Locking, Receptacle

51740-10409604ALF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAmphenol
Reach Compliance Codecompliant
Board mount optionsSPLIT BOARD LOCK
body width0.47 inch
subject depth0.5 inch
body length5.05 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact arrangementS96P8
Contact completed and terminatedTin (Sn)
Contact point genderFEMALE
Contact materialCOPPER ALLOY
Contact resistance20 mΩ
Contact styleHYBRID
Dielectric withstand voltage2500VDC V
Durability200 Cycles
maximum insertion force.973 N
Insulation resistance10000000000 Ω
insulator materialGLASS FILLED THERMOPLASTIC
JESD-609 codee3
Manufacturer's serial number51740
Mixed contactsYES
Installation option 1LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.135 inch
Termination typeSOLDER
Total number of contacts104
Evacuation force-minimum value.17792 N
PDM: Rev:R
STATUS:
Released
Printed: Dec 20, 2010
.
Summer, are you lazy?
When the weather is hot, you can grill directly on the stones. But sitting in front of the computer seems too lazy, right?...
zqjqq88 Talking
Wince burning problem
I rebooted after burning wince's nboot. I got this error: wince nand boot v1.00 mar 22 2007 00:02:34 picture boot wince nand boot v1.00 mar 22 2007 12:25:45 dwEntry is 0x00000001 ECC ERROR: 0x00000020...
zhang_shuai2005 Embedded System
STM8ADC and GPIO operation questions
STM8S105K6PB0PB1 > GPIO outputPB2The problem I am facing now is that after AIN2 ADC is initialized, AIN2 can collect data normally, but the PB0 status cannot be read. Have I encountered another BUG......
caobenda stm32/stm8
I use ATmega32's JTAG, why does the connection always fail? ? Please help
I use ATmega32 JTAG. First of all, the circuit is correct. I have verified it many times. The chip is also new. In addition, Jtag ports 1, 3, 5, and 9 are all connected to pull-up resistors. When prog...
zixialong Microchip MCU
[TI's First Low Power Design Competition] Micro LCR Tester - Hardware Part 4
This article will introduce the power supply part of LCRThe figure above is the principle block diagram of the power supply part. The right side is a typical single-button switch circuit. The switch i...
snoweaglemcu Microcontroller MCU
In 44B0, after an interrupt comes, I_ISPR in HandlerIRQ is 0. What should I do?
The host computer uses 44B0, and communicates with the lower computer through UART1 (RS485, baud rate 4800). The lower computer sends 32 bytes every 400 milliseconds, and the host computer responds wi...
chennan Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2112  2579  2104  2222  2482  43  52  45  50  42 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号