EEWORLDEEWORLDEEWORLD

Part Number

Search

2200GA3F002B3SA

Description
Strain Guage Sensor, Absolute, -15Psi Min, 15Psi Max, 0.25%, 0.20-10.20V, Cylindrical
CategoryThe sensor    Sensor/transducer   
File Size507KB,4 Pages
ManufacturerGems Sensors & Controls
Download Datasheet Parametric View All

2200GA3F002B3SA Overview

Strain Guage Sensor, Absolute, -15Psi Min, 15Psi Max, 0.25%, 0.20-10.20V, Cylindrical

2200GA3F002B3SA Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Reach Compliance Codeunknow
Maximum accuracy(%)0.25%
shellSTAINLESS STEEL
Nominal offset0.20V
Maximum operating temperature125 °C
Minimum operating temperature-40 °C
Output range0.20-10.20V
Output typeANALOG VOLTAGE
Package Shape/FormCYLINDRICAL
port type1/4 NPT
Maximum pressure range15 Psi
Minimum pressure range-15 Psi
Pressure sensing modeABSOLUTE
Sensor/Transducer TypePRESSURE SENSOR,STRAIN GUAGE
Maximum supply voltage35 V
Minimum supply voltage1.5 V
Termination typeDIN 9.4MM W/O MATE
Base Number Matches1
LC measurement tool-----Three, LM311 test
I searched around at home and found an LM311, and started to work on it according to the schematic diagram. Since I didn't have a frequency meter or an oscilloscope, I used a small speaker to experime...
tagetage 51mcu
Looking for a simple function signal generator design
Urgently seeking a simple function signal generator design...
ainiyijiao MCU
Some minor problems with the cordic algorithm for calculating sine and cosine functions
The above is the simulation waveform of the cordic algorithm for the sine and cosine functions. I don't quite understand why the sine and cosine results are 44, 50 (greater than 1), etc. The question ...
xuhongming FPGA/CPLD
MicroPython programming environment——Pycharm
I am used to PyCharm, so it is not easy to use uPyCraft, mainly because there is no code prompt Of course, it is not so easy to use PyCharm well.PyCharm build:Chinese version Cracking Installing the M...
lemon1394 MicroPython Open Source section
The board has been soldered, the GPIO has been turned on, and the JLINK debugger is used, which is quite convenient.
The board has been soldered, the GPIO has been turned on, and the JLINK debugger is used, which is quite convenient. Textures and Code...
damiaa DIY/Open Source Hardware
EEDrone open source quadrotor from scratch (6) -- FreeRTOS CLI debugging
[i=s] This post was last edited by lb8820265 on 2017-2-17 10:28 [/i] [align=left][font=微软雅黑][size=3] ST made an important upgrade to the library files of STM32F7 at the end of 2016, and launched the L...
lb8820265 DIY/Open Source Hardware

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 52  1887  2310  184  2560  2  38  47  4  52 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号