EEWORLDEEWORLDEEWORLD

Part Number

Search

GUB-GM8ALF-01-3572-D-B

Description
Array/Network Resistor, Isolated, Thin Film, 1.2W, 35700ohm, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 2244, DIP, ROHS COMPLIANT
CategoryPassive components    The resistor   
File Size493KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance  
Download Datasheet Parametric View All

GUB-GM8ALF-01-3572-D-B Overview

Array/Network Resistor, Isolated, Thin Film, 1.2W, 35700ohm, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 2244, DIP, ROHS COMPLIANT

GUB-GM8ALF-01-3572-D-B Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerTT Electronics plc
package instructionSMT, 2244
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresULTRA PRECISION
structureMolded
Component power consumption0.16 W
The first element resistor35700 Ω
JESD-609 codee3
Manufacturer's serial numberGUB
Installation featuresSURFACE MOUNT
Network TypeISOLATED
Number of components1
Number of functions8
Number of terminals16
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height2.286 mm
Package length11.176 mm
Package shapeRECTANGULAR PACKAGE
Package formSMT
Package width5.588 mm
Rated power dissipation(P)1.2 W
Rated temperature70 °C
resistance35700 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesGUB
size code2244
surface mountYES
technologyTHIN FILM
Temperature Coefficient100 ppm/°C
Temperature coefficient tracking5 ppm/°C
Terminal surfaceMatte Tin (Sn)
Terminal shapeGULL WING
Tolerance0.5%
TaNFilm
®
Small Outline Surface
Mount Resistor Network
GUB Series
Thin film on ceramic technology
0.220” and 0.300” sizes available
RoHS compliant version available
DESC 87012 and 87013 available
Standard JEDEC packages for automatic placement equipment
Compliant leads to
compensate for
thermal expansion
and contractions.
IRC Advanced Film Division
Ultra precision tantalum
nitride resistance element
on high purity alumina.
Rugged, molded
construction.
IRC’s TaNFilm®, Small Outline Integrated Circuit resistor networks are ideally suited for surface mounting.
The 0.05 inch lead spacing provides higher lead density, increased component count, lower installed resistor
cost, and better reliability. They are ideally suited for the latest surface mount assembly techniques, and each
lead can be 100% visually inspected. The compliant leads relieve thermal expansion and contraction stressed
created by soldering and temperature excursions.
The tantalum nitride film system provides precision tolerance, exceptional TCR tracking, and low noise.
TaNFilm® provides stability, high reliability, and long life characteristics. Testing has demonstrated performance
exceeding MIL-PRF-83401 characteristics H.
Electrical Data
GM Type
Resistance Range (Ω)
GL Type
Absolute Tolerance
Ratio Tolerance To R1
TCR (ppm/°C)
TCR Tracking To R1 (ppm°C)
Operating Temperature Range
Noise
Substrate
Custom circuits and special testing available.
Schem A: 10 to 200K
Schem B: 10 to 1000K
Schem A: 10 to 150K
Schem B: 10 to 75K
Available to ±0.1%
Available to ±0.05%
±25, ±50, ±100
±5
-55°C to +125°C
Less than -25 dB
High purity alumina substrate
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
GUB Series Issue November 2008 Sheet 1 of 3
Non-inverting proportional amplifier feedback resistor setting
I would like to ask you guys, for the op amp's inverse proportional amplifier circuit (as shown in the figure), how to correctly select the values of R1 and R2 under the same ratio? Are there any rest...
ericzh Analog electronics
I encountered a problem about Keil today
In the past few days, I have developed some functions of TouchGFX and added controls dynamically. It was relatively smooth during computer simulation. However, when it was burned to the development bo...
PowerWorld Programming Basics
Cumulative error analysis and clock frequency optimization for UART communication in MSP430FR2311
[i=s]This post was last edited by Aguilera on 2019-1-9 11:00[/i] [align=left][size=3][color=#ffffff] [/color][/size][size=3][color=#000000][backcolor=white] In UART communication design, engineers wil...
Aguilera Microcontroller MCU
How to configure the option bytes of stm8 in software
I want to ask you this question too....
6562748 stm32/stm8
HTC Desire S G12 Teardown
[size=10.5000pt] [/size] [font=微软雅黑][size=3]I am bored, and here I am again~~~~:pleased:[/size][/font] [font=微软雅黑][size=3]This time it is HTC Desire S, a phone I bought a few years ago. I accidentally...
国土安全局 Creative Market
[Shanghai Hangxin ACM32F070 development board + touch function evaluation board] Voltage meter implementation and ADC performance rough test
Preface This time, based on ADC and segment code display, the function of a voltmeter is realized. process Based on LCD_TK. Use the upper 4 digits to display the value in mV. From the schematic diagra...
qinyunti Domestic Chip Exchange

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2906  2829  664  485  896  59  57  14  10  19 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号