Datasheet
R8C/33D Group
RENESAS MCU
REJ03B0287-0100
Rev.1.00
Mar 31, 2010
1.
1.1
Overview
Features
The R8C/33D Group of single-chip MCUs incorporates the R8C CPU core, employing sophisticated instructions
for a high level of efficiency. With 1 Mbyte of address space, and it is capable of executing instructions at high
speed. In addition, the CPU core boasts a multiplier for high-speed operation processing.
Power consumption is low, and the supported operating modes allow additional power control. These MCUs are
designed to maximize EMI/EMS performance.
Integration of many peripheral functions, including multifunction timer and serial interface, reduces the number of
system components.
1.1.1
Applications
Electronic household appliances, office equipment, audio equipment, consumer equipment, etc.
REJ03B0287-0100 Rev.1.00
Mar 31, 2010
Page 1 of 42
R8C/33D Group
1. Overview
1.1.2
Specifications
Tables 1.1 and 1.2 outline the Specifications for R8C/33D Group.
Table 1.1
Item
CPU
Specifications for R8C/33D Group (1)
Function
Central processing
unit
Specification
R8C CPU core
• Number of fundamental instructions: 89
• Minimum instruction execution time:
50 ns (f(XIN) = 20 MHz, VCC = 2.7 to 5.5 V)
200 ns (f(XIN) = 5 MHz, VCC = 1.8 to 5.5 V)
• Multiplier: 16 bits × 16 bits
→
32 bits
• Multiply-accumulate instruction: 16 bits × 16 bits + 32 bits
→
32 bits
• Operation mode: Single-chip mode (address space: 1 Mbyte)
Refer to
Table 1.3 Product List for R8C/33D Group.
• Power-on reset
• Voltage detection 3 (detection level of voltage detection 0 and voltage
detection 1 selectable)
• Input-only: 1 pin
• CMOS I/O ports: 27, selectable pull-up resistor
• High current drive ports: 27
• 4 circuits: XIN clock oscillation circuit,
XCIN clock oscillation circuit (32 kHz),
High-speed on-chip oscillator (with frequency adjustment function),
Low-speed on-chip oscillator
• Oscillation stop detection: XIN clock oscillation stop detection function
• Frequency divider circuit: Dividing selectable 1, 2, 4, 8, and 16
• Low power consumption modes:
Standard operating mode (high-speed clock, low-speed clock, high-speed
on-chip oscillator, low-speed on-chip oscillator), wait mode, stop mode
Real-time clock (timer RE)
• Number of interrupt vectors: 69
• External Interrupt: 7 (INT × 3, Key input × 4)
• Priority levels: 7 levels
• 14 bits × 1 (with prescaler)
• Reset start selectable
• Low-speed on-chip oscillator for watchdog timer selectable
8 bits × 1 (with 8-bit prescaler)
Timer mode (period timer), pulse output mode (output level inverted every
period), event counter mode, pulse width measurement mode, pulse period
measurement mode
8 bits × 1 (with 8-bit prescaler)
Timer mode (period timer), programmable waveform generation mode (PWM
output), programmable one-shot generation mode, programmable wait one-
shot generation mode
16 bits × 1 (with 4 capture/compare registers)
Timer mode (input capture function, output compare function), PWM mode
(output 3 pins), PWM2 mode (PWM output pin)
8 bits × 1
Real-time clock mode (count seconds, minutes, hours, days of week), output
compare mode
Clock synchronous serial I/O/UART
Clock synchronous serial I/O/UART, I
2
C mode (I
2
C-bus),
multiprocessor communication function
10-bit resolution × 12 channels, includes sample and hold function, with sweep
mode
2 circuits
Memory
Power Supply
Voltage
Detection
I/O Ports
ROM, RAM
Voltage detection
circuit
Programmable I/O
ports
Clock generation
circuits
Clock
Interrupts
Watchdog Timer
Timer
Timer RA
Timer RB
Timer RC
Timer RE
Serial
Interface
A/D Converter
Comparator B
UART0
UART2
REJ03B0287-0100 Rev.1.00
Mar 31, 2010
Page 2 of 42
R8C/33D Group
1. Overview
Table 1.2
Item
Flash Memory
Specifications for R8C/33D Group (2)
Function
Specification
• Programming and erasure voltage: VCC = 2.7 to 5.5 V
• Programming and erasure endurance: 1,000 times (program ROM)
• Program security: ROM code protect, ID code check
• Debug functions: On-chip debug, on-board flash rewrite function
f(XIN) = 20 MHz (VCC = 2.7 to 5.5 V)
f(XIN) = 5 MHz (VCC = 1.8 to 5.5 V)
Typ. 6.5 mA (VCC = 5.0 V, f(XIN) = 20 MHz)
Typ. 3.5 mA (VCC = 3.0 V, f(XIN) = 10 MHz)
Typ. 3.5
µA
(VCC = 3.0 V, wait mode (f(XCIN) = 32 kHz))
Typ. 2.0
µA
(VCC = 3.0 V, stop mode)
-20 to 85°C (N version)
-40 to 85°C (D version)
(1)
32-pin LQFP
Package code: PLQP0032GB-A (previous code: 32P6U-A)
Operating Frequency/Supply
Voltage
Current Consumption
Operating Ambient Temperature
Package
Note:
1. Specify the D version if D version functions are to be used.
REJ03B0287-0100 Rev.1.00
Mar 31, 2010
Page 3 of 42
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
