EEWORLDEEWORLDEEWORLD

Part Number

Search

PTN1010E8452BGT3

Description
RESISTOR, THIN FILM, 0.5 W, 0.1 %, 25 ppm, 84500 ohm, SURFACE MOUNT, 1010, CHIP, ROHS COMPLIANT
CategoryPassive components    The resistor   
File Size117KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance  
Download Datasheet Parametric View All

PTN1010E8452BGT3 Overview

RESISTOR, THIN FILM, 0.5 W, 0.1 %, 25 ppm, 84500 ohm, SURFACE MOUNT, 1010, CHIP, ROHS COMPLIANT

PTN1010E8452BGT3 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerVishay
package instructionSMT, 1010
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresANTI-SULFUR; LASER TRIMMABLE; NON-INDUCTIVE
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.838 mm
Package length2.667 mm
Package formSMT
Package width2.54 mm
method of packingTR
Rated power dissipation(P)0.5 W
Rated temperature70 °C
resistance84500 Ω
Resistor typeFIXED RESISTOR
size code1010
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal surfaceGold (Au) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage150 V
PTN
Vishay Thin Film
Commercial Thin Film Chip Resistors
FEATURES
Lead (Pb)-free or Sn/Pb terminations available
Pb-free
Moisture resistant
Available
High purity alumina substrate
RoHS*
Non-standard values available
COMPLIANT
Will pass + 85 °C, 85 % relative humidity and
10 % rated power
100 % visual inspected per MIL-PRF-55342
Very low noise and voltage coefficient (< - 30 dB)
Non-inductive
Laser-trimmed tolerances to ± 0.1 %
Wraparound resistance less than 10 mΩ
Epoxy bondable termination available
Actual Size
1505
SURFACE MOUNT
CHIPS
These chip resistors are available in both “top side” and
“wraparound” termination styles in a variety of sizes. They
incorporate self passivated, enhanced Tantalum Nitride
films, to give superior performance on moisture resistance,
voltage coefficient, power handling and resistance stability.
The terminations consist of an adhesion layer, a leach
resistant nickel barrier, and solder coating. This product will
out-perform all requirements of characteristic H of
MIL-PRF-55342.
CONSTRUCTION
Passivation
Tantalum
Nitride
Resistive Film
Solder
coating
Nickel barrier
High Purity
Alumina Substrate
Adhesion layer
TYPICAL PERFORMANCE
ABS
TCR
TOL
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Absolute TCR
Absolute Tolerance
Operating Temperature Range
Noise
CASE SIZE
0402
0502
0505
0603
0805
(1)
, 0705
(1)
1005
1010
1206
1505
2208
2010
2512
POWER RATING (mW)
50
100
150
150
200
250
500
400
400
750
800
1000
SPECIFICATIONS
Tantalum nitride
± 25 ppm/°C, ± 50 ppm/°C, ± 100 ppm/°C
± 1.0 %, ± 0.5 % and ± 0.1 %
- 55 °C to + 125 °C
< - 25 dB
MAX. WORKING VOLTAGE
75
75
75
75
100
100
150
200
150
150
200
200
RESISTANCE RANGE - (Ω)
20 - 35K
20 - 65K
20 - 130K
10 - 80K
10 - 301K
10 - 301K
50 - 600K
10 - 1M
10 - 1M
10 - 1.75M
10 - 2M
10 - 3M
- 55 °C to + 125 °C
+ 25 °C
CONDITIONS
Note
(1)
0705 and 0805 are the same (only use 0805 when ordering)
* Pb containing terminations are not RoHS compliant, exemptions may apply
Document Number: 60026
Revision: 23-Jan-09
For technical questions, contact: thin-film@vishay.com
www.vishay.com
55
Phase-locked loop (PLL) detailed explanation
A phase-locked loop is a circuit or module used in a communication receiver to process the received signal and extract the phase information of a clock from it. In other words, for the received signal...
子乐 Analog electronics
[AN-1157 Application Note] Tuning the Extended Kalman Filter in the ADIS16480
Introduction: ADIS16480 is a MEMS inertial measurement unit (IMU) with a built-in three-axis accelerometer, a three-axis gyroscope, a three-axis magnetometer and a barometer....
EEWORLD社区 ADI Reference Circuit
Quartus II generates ROM and RAM embedded in OC8051
Use Quartus II to generate ROM and RAM to embed OC8051, write the HEX file generated by Keil into ROM, the purpose is to realize the hex specified function.Now the question is how to write this hex in...
woodys FPGA/CPLD
Please give me some advice on how to control the brightness of small lights with cc2530PWM
I want to implement a light switch experiment. The coordinator sends the light switch and brightness adjustment. The terminal that controls the light uses timer T1 to generate 1khz PWM to control the ...
doudongwade RF/Wirelessly
HPS and FPGA connection problem
Hello everyone, I am a humble boy and have just started working with SOC. When running the demo, I encountered the following problem and hope to get your guidance; The FPGA runs the sof file de1_soc_g...
花花打酱油 FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2600  2906  2786  557  1980  53  59  57  12  40 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号