TMP86PM29A datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > semiconductor> The embedded processor and controller> TMP86PM29A

TMP86PM29A: Description8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64; Categorysemiconductor The embedded processor and controller; File Size267KB，13 Pages; ManufacturerToshiba Semiconductor; Websitehttp://toshiba-semicon-storage.com/

Download Datasheet Parametric Compare View All

TMP86PM29A Overview

8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64

TMP86PM29A Parametric

Parameter Name	Attribute value
Number of functions	1
Number of terminals	64
Maximum operating temperature	85 Cel
Minimum operating temperature	-40 Cel
Maximum supply/operating voltage	3.6 V
Minimum supply/operating voltage	2.7 V
Rated supply voltage	3.3 V
External data bus width	0.0
Number of input and output buses	39
Line speed	16 MHz
Processing package description	10 × 10 MM, 0.50 MM PITCH, PLASTIC, LQFP-64
Lead-free	Yes
EU RoHS regulations	Yes
state	DISCONTINUED
Craftsmanship	CMOS
packaging shape	SQUARE
Package Size	FLATPACK, LOW PROFILE, FINE PITCH
surface mount	Yes
Terminal form	GULL WING
Terminal spacing	0.5000 mm
terminal coating	NOT SPECIFIED
Terminal location	Four
Packaging Materials	Plastic/Epoxy
Temperature level	INDUSTRIAL
ADC channel	Yes
Address bus width	0.0
Number of digits	8
Maximum FCLK clock frequency	16 MHz
Microprocessor type	Microcontroller
PWM channel	Yes
ROM programming	FLASH

Preview

Download Datasheet

View All

TMP86FM29

Comparison table of TMP86C829B/H29B/M29B/PM29A/PM29B/C929AXB and TMP86FM29

TMP86C829B

TMP86CH29B

TMP86CM29B

ROM

8 K (Mask ROM)

16 K (Mask ROM)

32 K (Mask ROM)

512

1.5 K

42 pin

5 pin

10-bit AD converter

8 ch

18-bit timer

1 ch

8-bit timer

4 ch

8-bit UART / SIO

1 ch

32 seg

4 com

4 ch

1.8 to 5.5 V at 4.2 MHz

2.7 to 5.5 V at 8 MHz

4.5 to 5.5 V at 16 MHz

−40

to 85℃

−

N/A

1.8 to 5.25 V at 4.2 MHz

2.7 to 5.25 V at 8 MHz

4.5 to 5.25 V at 16 MHz

0 to 60°C

TMP86PM29A

TMP86PM29B

TMP86C929AXB

(Emulation chip)

(Note 3)

−

TMP86FM29F

Difference

32 K (OTP)

32 K (Flash)

RAM

I/O

External

Interrupt

AD Converter

Timer Counter

Serial Interface

LCD

Key-on

Wakeup

Operating

Voltage

in MCU Mode

Operating

Temperature

in MCU Mode

Writing to

Flash Memory

CPU Wait (Note 1)

1.5 K

−

42 pin (MCU part)

42 pin

5 pin

10-bit AD converter

8 ch

18-bit timer

1 ch

8-bit timer

4 ch

8-bit UART / SIO

1 ch

32 seg

4 com (Note 2)

4 ch

1.8 to 3.6 V at 4.2 MHz (External clock)

1.8 to 3.6 V at 8 MHz (Resonator)

2.7 to 3.6 V at 16 MHz

−40

to 85°C

2.7 to 3.6V at 16 MHz

25°C

5°C

Available

Note 1: The CPU wait is a CPU halt function for stabilizing of power supply of Flash memory. The CPU wait

period is as follows. In the CPU wait period except RESET, CPU is halted but peripheral functions

are not halted. Therefore, if the interrupt occurs during the CPU wait period, the interrupt latch is set.

In this case, if the IMF has been set to “1”, the interrupt service routine is executed after CPU wait

period. For details refer to 2.14 “Flash Memory” in TMP86FM29 data sheet.

Thus, even if the same software is executed in 86FM29 and 86C829B/H29B/M29B/PM29A/PM29B

/C929AXB, the operation process is not the same. Therefore, when the final operating confirmation

on target application is executed for software development of Mask ROM Product

(86C829B/H29B/M29B), not the Flash product (86FM29) but the OTP product (86PM29A/PM29B)

should be used.

Condition

After reset release

Changing from STOP mode to NORMAL mode

(at EEPCR<MNPWDW>

“1”)

Changing from STOP mode to SLOW mode

(at EEPCR<MNPWDW>

“1”)

Changing from IDLE0/1/2 mode to NORMAL mode

(at EEPCR<ATPWDW>

“0”)

Changing from SLEEP0/1/2 mode to SLOW mode

(at EEPCR<ATPWDW>

“0”)

Wait Time

2 /fc[s]

2 /fs[s]

2 /fc[s]

2 /fs[s]

Halt/Operate

CPU

Halt

Peripherals

Halt

Operate

2004-03-01

TMP86FM29

CMOS 8-Bit Microcontroller

TMP86FM29UG/FG

The TMP86FM29 is the high-speed, high-performance and low power consumption 8-bit

microcomputer, including FLASH, RAM, LCD driver, multi-function timer/counter, serial interface

(UART/SIO), a 10-bit AD converter and two clock generators on chip.

Product No.

TMP86FM29UG

TMP86FM29FG

FLASH

32768

8 bits

RAM

1536

8 bits

Package

P-LQFP64-1010-0.50E

P-QFP64-1414-0.80C

Emulation Chip

TMP86C929AXB

Feautures

♦

•

8-bit single chip microcomputer TLCS-870/C series

Instruction execution time: 0.25

µs

(at 16 MHz)

122

µs

(at 32.768 kHz)

132 types and 731 basic instructions

19 interrupt sources (External: 5, Internal: 14)

Input/Output ports (39 pins)

(Out of which 24 pins are also used as SEG pins)

18-bit timer counter: 1 ch

Timer, Event counter,

Pulse width measurement,

Frequencymeasurement modes

8-bit timer counter: 4 ch

•

Timer, Event counter,

PWM output, Programmable divider output,

PPG output modes

Time Base Timer

Divider output function

030619EBP1

P-LQFP64-1010-0.50E

TMP86FM29UG

P-QFP64-1414-0.80C

♦

TMP86FM29FG

♦

•

The information contained herein is subject to change without notice.

•

The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by

TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by

implication or otherwise under any patent or patent rights of TOSHIBA or others.

•

TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general

can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the

buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and

to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or

damage to property.

In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the

most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling

Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc..

•

The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal

equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are

neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or

failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy

control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control

instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document

shall be made at the customer’s own risk.

•

The products described in this document are subject to the foreign exchange and foreign trade laws.

•

TOSHIBA products should not be embedded to the downstream products which are prohibited to be produced and sold, under any

law and regulations.

•

For a discussion of how the reliability of microcontrollers can be predicted, please refer to Section 1.3 of the chapter entitled Quality

and Reliability Assurance/Handling Precautions.

86FM29-1

2004-03-01

TMP86PM29A Related Products

	TMP86PM29A	TMP86C929AXB	TMP86CH29B	TMP86C829B	TMP86CM29B	TMP86PM29B	TMP86FM29
Description	8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64	8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64	8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64	8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64	8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64	8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64	8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64
Number of functions	1	1	1	1	1	1	1
Number of terminals	64	64	64	64	64	64	64
Maximum operating temperature	85 Cel	85 Cel	85 Cel	85 Cel	85 Cel	85 Cel	85 Cel
Minimum operating temperature	-40 Cel	-40 Cel	-40 Cel	-40 Cel	-40 Cel	-40 Cel	-40 Cel
Maximum supply/operating voltage	3.6 V	3.6 V	3.6 V	3.6 V	3.6 V	3.6 V	3.6 V
Minimum supply/operating voltage	2.7 V	2.7 V	2.7 V	2.7 V	2.7 V	2.7 V	2.7 V
Rated supply voltage	3.3 V	3.3 V	3.3 V	3.3 V	3.3 V	3.3 V	3.3 V
External data bus width	0.0	0.0	0.0	0.0	0.0	0.0	0.0
Number of input and output buses	39	39	39	39	39	39	39
Line speed	16 MHz	16 MHz	16 MHz	16 MHz	16 MHz	16 MHz	16 MHz
Processing package description	10 × 10 MM, 0.50 MM PITCH, PLASTIC, LQFP-64	10 × 10 MM, 0.50 MM PITCH, PLASTIC, LQFP-64	10 × 10 MM, 0.50 MM PITCH, PLASTIC, LQFP-64	10 × 10 MM, 0.50 MM PITCH, PLASTIC, LQFP-64	10 × 10 MM, 0.50 MM PITCH, PLASTIC, LQFP-64	10 × 10 MM, 0.50 MM PITCH, PLASTIC, LQFP-64	10 × 10 MM, 0.50 MM PITCH, PLASTIC, LQFP-64
Lead-free	Yes	Yes	Yes	Yes	Yes	Yes	Yes
EU RoHS regulations	Yes	Yes	Yes	Yes	Yes	Yes	Yes
state	DISCONTINUED	DISCONTINUED	DISCONTINUED	DISCONTINUED	DISCONTINUED	DISCONTINUED	DISCONTINUED
Craftsmanship	CMOS	CMOS	CMOS	CMOS	CMOS	CMOS	CMOS
packaging shape	SQUARE	SQUARE	SQUARE	SQUARE	SQUARE	SQUARE	SQUARE
Package Size	FLATPACK, LOW PROFILE, FINE PITCH	FLATPACK, LOW PROFILE, FINE PITCH	FLATPACK, LOW PROFILE, FINE PITCH	FLATPACK, LOW PROFILE, FINE PITCH	FLATPACK, LOW PROFILE, FINE PITCH	FLATPACK, LOW PROFILE, FINE PITCH	FLATPACK, LOW PROFILE, FINE PITCH
surface mount	Yes	Yes	Yes	Yes	Yes	Yes	Yes
Terminal form	GULL WING	GULL WING	GULL WING	GULL WING	GULL WING	GULL WING	GULL WING
Terminal spacing	0.5000 mm	0.5000 mm	0.5000 mm	0.5000 mm	0.5000 mm	0.5000 mm	0.5000 mm
terminal coating	NOT SPECIFIED	NOT SPECIFIED	NOT SPECIFIED	NOT SPECIFIED	NOT SPECIFIED	NOT SPECIFIED	NOT SPECIFIED
Terminal location	Four	Four	Four	Four	Four	Four	Four
Packaging Materials	Plastic/Epoxy	Plastic/Epoxy	Plastic/Epoxy	Plastic/Epoxy	Plastic/Epoxy	Plastic/Epoxy	Plastic/Epoxy
Temperature level	INDUSTRIAL	INDUSTRIAL	INDUSTRIAL	INDUSTRIAL	INDUSTRIAL	INDUSTRIAL	INDUSTRIAL
ADC channel	Yes	Yes	Yes	Yes	Yes	Yes	Yes
Address bus width	0.0	0.0	0.0	0.0	0.0	0.0	0.0
Number of digits	8	8	8	8	8	8	8
Maximum FCLK clock frequency	16 MHz	16 MHz	16 MHz	16 MHz	16 MHz	16 MHz	16 MHz
Microprocessor type	Microcontroller	Microcontroller	Microcontroller	Microcontroller	Microcontroller	Microcontroller	Microcontroller
PWM channel	Yes	Yes	Yes	Yes	Yes	Yes	Yes
ROM programming	FLASH	FLASH	FLASH	FLASH	FLASH	FLASH	FLASH

Recommended Resources

single-ended input flip-flop

DC converter circuit for servo instrument

A simple and practical energy-consuming brake

555 electroplating timing automatic shutdown reporting circuit

flash trigger circuit

One of the single-control regulated power supplies

2440 WinCE 6.0 image download and run error: My qq2440 + WinCE 6.0, nk.bin can be compiled, but an error occurs when running after downloading. The error is as follows: Enter your selection: w Clear the free memory Please send the Image through ...; hustvic Embedded System

How can I tell the difference between the small square in the selection box and a check mark in the selection box in Catelog?: What is the difference between these two items when changing Catelog...; 0211liucheng Embedded System

What is the specific register configuration of the ADA2200 EVAL CN0371 board?: I don't have a matching development board, only an EVAL CN0371 board with an external STM32 driver. I want to ask what the original 2200 and 7192 parameter settings are? If you have an E100 sensor, pl...; huixiesui ADI Reference Circuit

There is nothing that cannot be embedded, only imagination can be used. Popular Science of Embedded Systems: Nowadays, the development of IoT, AI, and 5G cannot be separated from embedded systems. It is like a Lego puzzle. As long as you know how to "play", unexpected performance will occur. So what exactly ...; okhxyyo Embedded System

Does anyone know how to modify the encoding of the Linux vi editor?: From EEWORLD cooperation group: arm linux fpga embedded 0 (49900581) Group leader: wangkj[/url] Hello comrades, who knows how to modify the encoding of the Linux vi editor? When using local import, it...; 天天天蓝 Test/Measurement

When the program is executed, why does my serial port debugging assistant not respond at all? Yesterday, there were still garbled codes?: ...; lixingping1125 Microcontroller MCU

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components