When using EV in 2812, you can directly write EVx.ACTRx to directly control the forced high and forced low of PWM output. How should I configure it on the device using ePWM so that it can be forced hi...
Looking for RF wake-up solution, 125KHz low frequency or high frequency is fine, as long as it can wake up. Wake-up distance <1.2m; antenna area is about 1.2mX1.2m; if you have a solution, please cont...
MCLK represents the CPU operation and system clock. 430 executes a simple instruction in one clock cycle. Why does it take the same time to execute the same code when MCLK=REFOCLK (32768HZ) and MCLK=X...
[i=s] This post was last edited by electrics on 2016-9-26 00:33 [/i] while(1) { if(((TIM2->SR&0X0001)==1)&&((TIM2->CCER & 0X0002)==0X0002)) //Falling edge trigger and judgment is reaching the maximum ...
Single-choice questions 1. The transmission mode in which the microprocessor only starts the peripherals without intervening in the transmission process is _________ mode. A. Interrupt B. DMA C. Query...
Abstract: This paper introduces the main features, working principle and interface technology of DS2480B UART/RS232 to single bus protocol converter, and specifically explains the application of DS248...
Emergency hand-held lamps powered by 6V maintenance-free batteries are widely used in rural areas. The charger used is a transformer step-down and single diode half-wave rectifier, and the charging...[Details]
0 Introduction
With the development of my country's economy, the number of motor vehicles continues to increase. The growth of existing roads and other hardware facilities can no longer meet t...[Details]
Analog engineers have traditionally struggled with complexity when designing power supplies that required multiple outputs, dynamic load sharing, hot-swap, or extensive fault-handling capabilities....[Details]
All electronic design engineers and scientists have performed electrical signal analysis, or signal analysis for short. Through this basic measurement, they can gain insight into signal details and...[Details]
The reason for the light decay of white LEDs: the decline of phosphor performance
So far, the rapid decline of the luminous performance of white light LEDs, especially low-power white light LE...[Details]
0 Introduction
With the development of society, people pay more and more attention to security work. Monitoring products have been used in various fields instead of being used only in importan...[Details]
1. Introduction
At present, most lighting equipment still uses traditional energy for lighting. Making full use of solar energy as the energy supply for lighting equipment is of great si...[Details]
Overview:
This paper introduces a method of connecting a CAN-bus network with Ethernet to form a medium-sized remote monitoring/data transmission network.
CAN (Controller Area Network) is ...[Details]
1. Introduction to CIF Board
Fieldbus integration based on PC system
Whether it is a master or a slave, fieldbus has won unanimous praise in the field of PC-based automation. For more...[Details]
Many battery-powered systems require a visual indicator to show when the battery needs to be replaced. LEDs are commonly used for this purpose, but they consume at least 10mA of current. This con...[Details]
Liquid crystal display (LCD) panels have a wide range of applications, from small portable electronic devices to large fixed devices, including digital cameras, laptops, personal data assistants, d...[Details]
Key Points
1. Now, in addition to high-end smartphones and tablets, users also expect to use touch screens in other applications, and they are gradually appearing in cars and instruments.
...[Details]
When the so-called "copycat phones" that flood the domestic mobile phone market move towards large screens, stereo amplifiers, touch controls, and even GPS navigation and mobile TV, the homogeneity...[Details]
Portable power applications are broad and varied. Products range from wireless sensor nodes with average power consumption of only a few microwatts to in-vehicle medical or data acquisition systems...[Details]
1 Introduction
Power supply ripple will interfere with the normal operation of electronic equipment, causing malfunctions such as computer crashes, data processing errors and control system fa...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
