EEWORLDEEWORLDEEWORLD

Part Number

Search

WCTN20216202D

Description
RES NET,THIN FILM,162K OHMS,100WV,.5% +/-TOL,-25,25PPM TC,0303 CASE
CategoryPassive components    The resistor   
File Size118KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

WCTN20216202D Overview

RES NET,THIN FILM,162K OHMS,100WV,.5% +/-TOL,-25,25PPM TC,0303 CASE

WCTN20216202D Parametric

Parameter NameAttribute value
MakerVishay
package instructionSMT, 0303
Reach Compliance Codeunknown
ECCN codeEAR99
structureChip
Manufacturer's serial numberCTN
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
GuidelineMIL-STD-883
resistance162000 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesCTN
size code0303
Temperature Coefficient-25,25 ppm/°C
Tolerance0.5%
Operating Voltage100 V
CTN
Vishay Electro-Films
Nichrome Thin Film, Center Tapped Resistors
CHIP
RESISTORS
FEATURES
Wire bondable
Product may not
be to scale
Center tap feature
Chip size: 0.030 inches square
Resistance range total: 10
Ω
to 1 MΩ
Ratio tolerances to: 0.1 %
Resistor material: Nichrome
Oxidized silicon substrate for good power dissipation
The CTN series is a center tapped nichrome resistor chip
providing excellent stability at 250 mW power levels. The
CTN offers the designer flexibility in use as either a single
value resistor or as two resistors with a center tap feature.
The CTNs six bonding pads allows the user increased layout
flexibility.
The CTNs are manufactured using Vishay Electro-Films
(EFI) sophisticated thin film equipment and manufacturing
technology. The CTNs are 100 % electrically tested and
visually inspected to MIL-STD-883.
APPLICATIONS
The CTN center-tapped resistor chips are used mainly in feedback circuits of amplifiers where ratio matching, high power and
tracking between two resistors is critical.
Recommended for Hermetic environment where die is not exposed to moisture.
For low values, the resistance of the six bonding-pad configurations can vary, depending on the method of measurement used.
Vishay EFI measures low-value resistors by the four wire Kelvin technique.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES AND TOLERANCES
Tightest Standard Tolerance Available
0.5 %
0.1 %
± 10 ppm/°C
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
PROCESS CODE
CLASS H*
203
202
200
201
*MIL-PRF-38534 inspection criteria
1 MΩ
CLASS K*
263
262
260
261
10
Ω
100
Ω
200
Ω
1 kΩ
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
TCR Tracking Between Halves (R
A
/R
B
)
Center Tap Ratio,
R
A
/R
B
Tolerance
Noise, MIL-STD-202, Method 308, 100
Ω
- 250 kΩ
Stability, 1000 h, + 125 °C, 125 mW
Operating Temperature Range
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
DC Power Rating at + 70 °C (Derated to Zero at + 175 °C)
* 20 ppm/°C for
R
< 20
www.vishay.com
76
For technical questions, contact: efi@vishay.com
Document Number: 61024
Revision: 12-Mar-08
± 2 ppm/°C *
1 ± 1 % standard
- 35 dB typ.
± 0.1 %
ΔR/R
- 55 °C to + 125 °C
200 V
10
12
min.
100 V max.
250 mW
About dsp5402 communication problem
I made a dsp5402 minimum system, which can make a light flash, but it can't work after connecting the communication part. It can't connect to the simulator. It can connect occasionally, but it will pr...
cdfly DSP and ARM Processors
WinDriver interrupt problem
It seems that the efficiency of receiving interrupts using windriver is not high. How can I set it up to write PlugIn? I tried the operation described in the document and it doesn't seem to work. It a...
lao3 Embedded System
Participate in the HELPER2416 development board scholarship program: Reconstructed modbus slave
I have been a bit busy recently and have missed a lot of work. Modbus is a commonly used communication protocol in the field of industrial control, and freemodbus has added a lot of convenience to eng...
hongyancl Embedded System
[Solved] CRC check code conversion
[i=s] This post was last edited by 416202554 on 2015-5-30 23:14 [/i] MSP430FR5969 supports hardware CRC checksum, but the checksum uses the CRC CCITT standard, while the existing host computer uses th...
416202554 Microcontroller MCU
Problems with multiple clocks in one module
If a module has multiple clock input signals, is this design reasonable? What problems will arise? How to deal with it?...
eeleader FPGA/CPLD
Control Siemens mobile phone problem ~
Can all Siemens phones be controlled by AT commands as long as they have a data cable? If not, can you recommend a few cheap models like C60 and C62? I've downloaded all the stuff......
zaq1 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 253  1634  1375  1727  2876  6  33  28  35  58 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号