EEWORLDEEWORLDEEWORLD

Part Number

Search

XSFP10735702C

Description
RES,SMT,THIN FILM,357K OHMS,100WV,.2% +/-TOL,-50,50PPM TC,0202 CASE
CategoryPassive components    The resistor   
File Size84KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

XSFP10735702C Overview

RES,SMT,THIN FILM,357K OHMS,100WV,.2% +/-TOL,-50,50PPM TC,0202 CASE

XSFP10735702C Parametric

Parameter NameAttribute value
MakerVishay
package instructionSMT, 0202
Reach Compliance Codeunknown
ECCN codeEAR99
structureChip
Manufacturer's serial numberSFP
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length0.558 mm
Package formSMT
Package width0.558 mm
method of packingTray
Rated power dissipation(P)0.25 W
GuidelineMIL-STD-883
resistance357000 Ω
Resistor typeFIXED RESISTOR
seriesSFP
size code0202
technologyTHIN FILM
Temperature Coefficient-50,50 ppm/°C
Tolerance0.2%
Operating Voltage100 V
SFP
Vishay Electro-Films
CHIP
RESISTORS
Thin Film Top-Contact Resistor
with Part Mark
FEATURES
Wire bondable
Product may not
be to scale
Part marked - 5 digits
Small size: 0.022 inches square
Resistance range: 1
Ω
to 1 MΩ
DC power rating: 250 mW
Oxidized silicon substrate for good power dissipation
Resistor material: Tantalum nitride, self passivating
Moisture resistant
The SFP series single-value resistor chips offer a small size,
wide ohmic value range and excellent power capacity.
The SFPs are part marked with resistance value allowing
user the ability to visually determine the resistance value of
the chip.
The SFPs are manufactured using Vishay Electro-Films
(EFI) sophisticated thin film equipment and manufacturing
technology.
The SFPs are 100 % electrically tested and visually
inspected to MIL-STD-883.
APPLICATIONS
Vishay EFI SFP small resistor chips are widely used in hybrid packages where space is limited and chip value marking is
important for identification. The die is part marked with the resistance value. Wire bonding is made to the two pads on the top of
the chip.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES AND TOLERANCES
Tightest Standard Tolerance Available
1%
0.5 %
PROCESS CODE
0.1 %
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
± 250 ppm/°C
CLASS H*
103
102
101
100
CLASS K*
108
107
106
105
1
Ω
10
Ω
30
Ω
100
Ω
200 k
Ω
430 k
Ω
620 k
Ω
1 M
Ω
* MIL-PRF-38534 inspection criteria
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
Noise, MIL-STD-202, Method 308
100
Ω
- 250 kΩ
< 100
Ω
or > 251 kΩ
Moisture Resistance, MIL-STD-202
Method 106
Stability, 1000 h, + 125 °C, 125 mW
Operating Temperature Range
Thermal Shock, MIL-STD-202,
Method 107, Test Condition F
High Temperature Exposure, + 150 °C, 100 h
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
DC Power Rating at + 70 °C (Derated to Zero at + 175 °C)
5 x Rated Power Short-Time Overload, + 25 °C, 5 s
Values above 1M available
www.vishay.com
40
For technical questions, contact: ff2bresistors@vishay.com
Document Number: 61000
Revision: 07-Mar-08
- 35 dB typ.
- 20 dB typ.
± 0.5 % max.
ΔR/R
± 0.25 % max.
ΔR/R
- 55 °C to + 125 °C
± 0.25 % max.
ΔR/R
± 0.5 % max.
ΔR/R
200 V
10
12
min.
100 V max.
250 mW
± 0.25 % max.
ΔR/R
Non-inverting proportional amplifier feedback resistor setting
I would like to ask you guys, for the op amp's inverse proportional amplifier circuit (as shown in the figure), how to correctly select the values of R1 and R2 under the same ratio? Are there any rest...
ericzh Analog electronics
I encountered a problem about Keil today
In the past few days, I have developed some functions of TouchGFX and added controls dynamically. It was relatively smooth during computer simulation. However, when it was burned to the development bo...
PowerWorld Programming Basics
Cumulative error analysis and clock frequency optimization for UART communication in MSP430FR2311
[i=s]This post was last edited by Aguilera on 2019-1-9 11:00[/i] [align=left][size=3][color=#ffffff] [/color][/size][size=3][color=#000000][backcolor=white] In UART communication design, engineers wil...
Aguilera Microcontroller MCU
How to configure the option bytes of stm8 in software
I want to ask you this question too....
6562748 stm32/stm8
HTC Desire S G12 Teardown
[size=10.5000pt] [/size] [font=微软雅黑][size=3]I am bored, and here I am again~~~~:pleased:[/size][/font] [font=微软雅黑][size=3]This time it is HTC Desire S, a phone I bought a few years ago. I accidentally...
国土安全局 Creative Market
[Shanghai Hangxin ACM32F070 development board + touch function evaluation board] Voltage meter implementation and ADC performance rough test
Preface This time, based on ADC and segment code display, the function of a voltmeter is realized. process Based on LCD_TK. Use the upper 4 digits to display the value in mV. From the schematic diagra...
qinyunti Domestic Chip Exchange

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1485  124  1435  103  826  30  3  29  17  43 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号