EEWORLDEEWORLDEEWORLD

Part Number

Search

DR1P5-24S05

Description
1-OUTPUT 1.5 W DC-DC REG PWR SUPPLY MODULE
Categoryaccessories   
File Size96KB,2 Pages
ManufacturerRSG Electronic Components GmbH
Websitehttp://www.rsg-electronic.de/de/
Download Datasheet View All

DR1P5-24S05 Overview

1-OUTPUT 1.5 W DC-DC REG PWR SUPPLY MODULE

VER:03
1 / 2
1.5 WATTS REGULATED OUTPUT POWER
LOW OUTPUT RIPPLE & NOISE
PI TYPE INPUT FILTER
500VDC ISOLATION VOLTAGE
HIGH EFFICIENCY UP TO 55%
STANDARD 24 PIN DIP PACKAGE & SMD TYPE PACKAGE
FIVE-SIDED EMI SHIELD
The DR1P5 series offer 1.5 watts of output power from a package in an IC compatible 24
pin DIP configuration without derating to 71ºC ambient temperature and pin to pin
compatible to MKC03 series. DR1P5 series have input voltage of 4.5-5.5, 10.8-13.2 and
21.6-26.4VDC. DR1P5 features 500VDC of isolation voltage. A safety designed meet to
EN60950-1 and UL60950-1. All models are particularly suited to telecommunications,
industrial, mobile telecom and test equipment applications.
T E C H N I C A L S P E C I F I C AT I O N
OUTPUT SPECIFICATIONS
Output power
Voltage accuracy
Minimum load
Line regulation
Load regulation
Cross regulation
Ripple and noise
Temperature coefficient
Short circuit protection
LL to HL at Full Load
25% to 100% FL
D05 output
others
Full load and nominal Vin
All specifications are typical at nominal input, full load and 25ºC otherwise noted
GENERAL SPECIFICATIONS
1.5 Watts max
± 4%
0%
± 0.3%
± 1.5%
± 0.5%
± 5%
50mVp-p
±0.02% / ºC, max
Short term
Efficiency
Isolation voltage
Isolation resistance
Isolation capacitance
Switching frequency
Design meet safety standard
Case material
Base material
Potting material
Dimensions
9
See table
500VDC, min
10 ohms, min
30pF, max
20KHz, min
IEC60950-1, UL60950-1,EN60950-1
Nickel-coated copper
Non-conductive black plastic
Epoxy (UL94-V0)
1.25 X 0.80 X 0.40 Inch
(31.8 X 20.3 X 10.2 mm)
16g (0.55oz)
18g (0.62oz)
5.531 x 10 hrs
6
Asymmetrical load 25% / 100% FL
20MHz bandwidth
INPUT SPECIFICATIONS
Input voltage range
5V nominal input
12V nominal input
24V nominal input
4.5 – 5.5VDC
10.8 – 13.2VDC
21.6 – 26.4VDC
Pi type
Weight
MTBF (Note 1)
DIP
SMD
Input filter
ENVIRONMENTAL SPECIFICATIONS
Operating temperature range
Maximum case temperature
Storage temperature range
-25ºC ~ +71ºC
+100ºC
-55ºC ~ +105ºC
Nature convection
20ºC/watt
MIL-STD-810D
10~55Hz, 10G, 30minutes along X,Y and Z
5% to 95% RH
OUTPUT POWER (%)
DR1P5-24S05 Derating Curve
100
75
50
25
0
-40 -25 -10 0
50
60
70
80
90 100
Thermal impedance
Thermal shock
Vibration
Relative humidity
Nature convection
EMC CHARACTERISTICS
Conducted emissions
Radiated emissions
ESD
Radiated immunity
Fast transient
Surge
Conducted immunity
EN55022
EN55022
EN61000-4-2
EN61000-4-3
EN61000-4-4
EN61000-4-5
EN61000-4-6
Class A
Class A
Perf. Criteria B
Perf. Criteria A
Perf. Criteria B
Perf. Criteria B
Perf. Criteria A
AMBIENT TEMPERATURE (ºC)
ELECTRONIC COMPONENTS
RSG
RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany
Tel. +49 69 984047-0 Fax +49 69 984047-77 info@rsg-electronic.de
www.rsg-electronic.de
Änderungen vorbehalten / subject to change without notice
Questions about LCD display
#include #define uint unsigned int #define uchar unsigned char sbit lcdrs=P1^0; sbit lcdrw=P1^1; sbit lcden=P1^2; void delay(uint z) { uint x,y; for(x=z;x 0;x--) for(y=110;y0;y--); } void write_com(uc...
liufengjing9 51mcu
Help, anyone who has used the MAX1898 power management chip?
As shown in the figure, I used a microcontroller and this chip to connect to make a charger. The capacitor between CT and RESTRT is 100nf. According to the formula in the data sheet, the charging time...
zxpla MCU
Where can I find the PHI EVM Controller information for the TI ADC acquisition board?
The ADC evaluation board below comes with a PHI EVM Controller. I don't know where to get the information. After ADS8588S EVM.exe is connected to a computer, can it realize the synchronous acquisition...
littleshrimp Analogue and Mixed Signal
Why does each device simulation model downloaded from TI's official website have many files after decompression?
Why does the device simulation model downloaded from TI's official website have many files after decompression? How should I use AD simulation?...
JFET Analogue and Mixed Signal
SDHC Standard
SDHC standard, I have uploaded it. If you have SDver1.0, please upload one too....
wall_e FPGA/CPLD
How to port WinCE kernel image and export SDK
My senior uses Linux operating system, and the ARM development board is installed with Linux kernel. I use WinCE operating system, and I want to port WinCE kernel image to the development board. We us...
gaohang Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 918  801  2316  1274  1394  19  17  47  26  29 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号