EEWORLDEEWORLDEEWORLD

Part Number

Search

10131693-00074C7LF

Description
Board Connector, 74 Contact(s), 2 Row(s), Male, Straight, 0.05 inch Pitch, Surface Mount Terminal, Locking, Black Insulator,
CategoryThe connector    The connector   
File Size197KB,2 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

10131693-00074C7LF Overview

Board Connector, 74 Contact(s), 2 Row(s), Male, Straight, 0.05 inch Pitch, Surface Mount Terminal, Locking, Black Insulator,

10131693-00074C7LF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7105790604
Reach Compliance Codecompliant
ECCN codeEAR99
YTEOL9.4
body width0.209 inch
subject depth0.22 inch
body length1.975 inch
Connector typeBOARD CONNECTOR
Contact completed and terminatedGold (Au)
Contact point genderMALE
Contact materialCOPPER ALLOY
contact modeRECTANGULAR
Contact resistance50 mΩ
Contact styleSQ PIN-SKT
Dielectric withstand voltage700VAC V
Durability100 Cycles
maximum insertion force2.1684 N
Insulation resistance100000000 Ω
Insulator colorBLACK
insulator materialPOLYETHYLENE
JESD-609 codee4
Plug contact pitch0.05 inch
Match contact row spacing0.05 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
PCB contact patternRECTANGULAR
PCB contact row spacing3.9116 mm
Plating thickness15u inch
polarization keyPOLARIZED HOUSING
Rated current (signal)1 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal pitch1.27 mm
Termination typeSURFACE MOUNT
Total number of contacts74
Evacuation force-minimum value.1946 N
PDS: Rev :C
STATUS:Released
Printed: Apr 06, 2016
Is it the inverter or the integrator circuit?
As shown The input Uin of the op amp is obtained from the -380VDC bus through resistor voltage division to obtain -3.5VDC Is the op amp in the figure a simple inverting 1:1 amplifier circuit, or is it...
shaorc Analog electronics
How to configure uclinux to automatically obtain an ip after arm is powered on?
How to configure uclinux to let arm automatically get ip after power on? My development board is S3C44B0. I heard that uclinux supports dhcp. 1. What should I choose when compiling uclinux 2.4 kernel ...
wawj1819 Linux and Android
Can first-tier devices do the job?
Previously, the sensor head was made by Honeywell combined with first-line devices. The SHT21 may be smaller in size. The I2C interface direct cable transmission requires signal preprocessing. Can fir...
bjwl_6338 DIY/Open Source Hardware
linux-2.6.34 kernel porting documentation [simple operation]
I just transplanted the kernel image file, put it on the development board and ran it for a while, and the system is running!!! Pictures speak louder than words...See the attached documentation for th...
37°男人 Embedded System
Introduction to the training for the 2013 Electronic Design Competition
[i=s] This post was last edited by paulhyde on 2014-9-15 03:11 [/i] Nanhua University Huang Zhiwei prepares for the 2013 Electronic Design Competition - Introduction to some information on training...
黄智伟 Electronics Design Contest
Please tell me about the assembly instructions related to AVR program jump
I've been working on the assembly of AVR recently and encountered some problems. I'd like to ask enthusiastic netizens to help me figure out what's going on. The development board I have is atmega128a...
lr2131 Microchip MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1761  2334  871  2062  1977  36  47  18  42  40 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号