EEWORLDEEWORLDEEWORLD

Part Number

Search

370LB003B12

Description
Water-Tight Cable Sealing Backshell
File Size67KB,2 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Download Datasheet View All

370LB003B12 Overview

Water-Tight Cable Sealing Backshell

370-003
Water-Tight Cable Sealing Backshell
with Strain Relief
Low Profile - Rotatable Coupling
370 F S 003 M 16 10 C 6
37
CONNECTOR
DESIGNATORS
Product Series
Connector
Designator
Angle and Profile
A = 90°
B = 45°
S = Straight
Basic Part No.
Length: S only
(1/2 inch increments:
e.g. 6 = 3 inches)
Strain Relief Style
(B, C, E)
Cable Entry (Tables IV, V)
Shell Size (Table I)
Finish (Table II)
A-F-H-L-S
ROTATABLE
COUPLING
Length ± .060 (1.52)
Min. Order Length 2.0 Inch
(See Note 6)
A Thread
(Table I)
O-Ring
Length ± .060 (1.52)
Min. Order Length 1.5 Inch
(See Note 6)
C Typ.
(Table I)
STYLE 2
(STRAIGHT
See Note 1)
.88 (22.4)
Max
E
(Table III)
G
(Table III)
F (Table III)
H (Table III)
STYLE 2
(45° & 90°
See Note 1)
STYLE B
(Table IV)
P
J
STYLE C
Medium Duty
(Table IV)
Clamping
Bars
STYLE E
Medium Duty
(Table V)
N (See
Note 4)
L
Cable
Range
K
Cable
Range
K
Cable
Range
M
© 2005 Glenair, Inc.
CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
E-Mail: sales@glenair.com
Series 37 - Page 14
About CAN interrupt of 8962
I would like to ask you. After my program enters the CAN interrupt, I use CANIntStatus (CAN0_BASE, CANI_INT_STS_CAUSE) to read, but why does it always return "0"? I have read a lot of documents, and d...
ZHANGXUEJIE Microcontroller MCU
TM4C123G cannot simulate TI routine timers. . .
[url] I am a beginner in M4 and want to create a new program by imitating the source program. I found that after setting various paths and predefined symbols, the compilation can pass, but the functio...
nemo1991 Microcontroller MCU
Transfer some new idle development boards, all of them are brand new
[i=s] This post was last edited by fesns on 2014-9-9 20:10 [/i]I am transferring some unused development boards on behalf of a friend. They are all brand new. [b] Transfer a brand new STM32F030R8 DISC...
fesns Buy&Sell
Seek advice from experts
This is the main control diagram of the circuit of my board. It has been simulated with proteus. There is no problem with the circuit measurement when soldering the circuit, but there is no response w...
lecdyx312 51mcu
What is the status of the STM32 pin after setting it to push-pull output?
I have a question!After the STM32 pin is reset, it is in high impedance input state. Then I configure the pin as push-pull output.But it does not assign a valueof 0 or 1. Does it output 0 or 1 at this...
niuqingjun stm32/stm8
SensorTile.boxr's personal experience
I just received my engineer's certificate. It took me two years to pass the exam and I finally got it after retaking it .Let’s get to the point It has been more than half a month since I received it. ...
黎某西 ST MEMS Sensor Creative Design Competition

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 275  815  2418  461  2161  6  17  49  10  44 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号