EEWORLDEEWORLDEEWORLD

Part Number

Search

ASM1834DF-T

Description
2-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8
CategoryPower/power management    The power supply circuit   
File Size248KB,10 Pages
ManufacturerALSC [Alliance Semiconductor Corporation]
Environmental Compliance
Download Datasheet Parametric View All

ASM1834DF-T Overview

2-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8

ASM1834DF-T Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerALSC [Alliance Semiconductor Corporation]
Parts packaging codeDIP
package instructionDIP,
Contacts8
Reach Compliance Codeunknow
ECCN codeEAR99
Adjustable thresholdNO
Analog Integrated Circuits - Other TypesPOWER SUPPLY SUPPORT CIRCUIT
JESD-30 codeR-PDIP-T8
JESD-609 codee3/e6
length9.59 mm
Number of channels2
Number of functions1
Number of terminals8
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Package body materialPLASTIC/EPOXY
encapsulated codeDIP
Package shapeRECTANGULAR
Package formIN-LINE
Peak Reflow Temperature (Celsius)NOT SPECIFIED
Certification statusNot Qualified
Maximum supply voltage (Vsup)5.5 V
Minimum supply voltage (Vsup)1.2 V
Nominal supply voltage (Vsup)5 V
surface mountNO
Temperature levelINDUSTRIAL
Terminal surfaceMATTE TIN/TIN BISMUTH
Terminal formTHROUGH-HOLE
Terminal pitch2.54 mm
Terminal locationDUAL
Maximum time at peak reflow temperatureNOT SPECIFIED
width7.62 mm
April 2005
rev 1.3
ASM1834/A/D
Dual 5V and 3.3V µP Power Supply Supervisor with Manual Reset
All devices operate over the extended industrial temperature
range. Devices are available in 8-pin DIP, surface mount 8-pin
SO and 8-Pin MicroSO packages. Die are also available.
General Description
The ASM1834 supervisors simultaneously monitor both 3.3V
and 5V power sources and generate reset signals when either
supply is out of tolerance. When an out-of-tolerance condition is
detected, the output-reset signal of the affected supply
becomes active and resets the system microprocessor/
microcontroller. On power-up and after the supply voltage
returns to an in-tolerance condition, the reset signal remains
active for approximately 350ms. This allows the power supply
and system microprocessor to stabilize.
Tolerance levels are independently selectable for both supplies.
Tolerance options are 5% and 10% percent for the 5V supply
and 10% and 20% percent for the 3.3V supply.
The ASM1834 and ASM1834D have push-pull reset output
stages. The ASM1834A reset outputs are open drain devices
that can both be connected to either 5V or 3.3V supply. The
ASM1834 and ASM1834A have active LOW reset outputs. The
ASM1834D has active HIGH reset outputs.
All devices can generate reset signals through an internally
debounced pushbutton reset input that affects both reset
outputs.
Key Features
Monitors 5V and 3.3V supplies simultaneously
5V and 3.3V power-on reset
350ms reset time
Debounced pushbutton reset input
Push-pull CMOS output
• ASM1834, ASM1834D
• Eliminates external pull-up resistors
• Active LOW (ASM1834), HIGH (ASM1834D)
Open Drain Output
• ASM1834A
• Active LOW
Selectable 5V and 3.3V trip point tolerance
Internal power drawn from highest input voltage, 5V or
3.3V
Precision temperature-compensated voltage reference and
comparator
Low cost surface mount SO, compact MicroSO and DIP
packages.
Wide operating temperature, -40°C to +85°C
Applications
Microprocessors
PDAs, Hand-held PCs
Embedded Controllers
Telecommunication Systems
Power Supplies
Wireless / Cellular Systems
Networking Hardware
Typical Operating Circuit
3.3V
+5V
ASM1834
5V
IN
3.3V
IN
RESET
PBRST
5VTOL GND 3.3VTOL
3.3V
5V
µP
RESET
GND
Alliance Semiconductor
2575 Augustine Drive . Santa Clara, CA 95054 . Tel: 408.855.4900 . Fax: 408.855.4999 . www.alsc.com
Notice: The information in this document is subject to change without notice
DA/AD conversion
In the application of digital systems, some measured physical quantities are usually sent to the digital system through sensors for processing; the output data obtained after processing is sent back t...
lk972105 MCU
Question A: It's difficult! Please help...
[i=s] This post was last edited by paulhyde on 2014-9-15 09:06 [/i] [size=12pt] Implementation help: How to implement, Phase tracking function: When ifREF changes within a given range and a non-resist...
电子爱好者 Electronics Design Contest
I am looking for a person who has experience in BIOS design and development to join the research and development team of a scientific research unit.
I was asked to help a national scientific research unit find an expert with experience in BIOS design and development. The unit is strong and has been engaged in this project for a long time. The sala...
mxcb2008 Embedded System
Competition among switching power supply industries
Competition between the switching power supply industry has a long history, and other industries are also fair competition, which can improve and promote the development of business and even the progr...
lwqzzp Power technology
Seeking a software development engineer. Those with strong integration ability can be given technical bonus shares!
We are engaged in multimedia players. Currently, we use MCU+DSP architecture (hard decoding). We do not rule out the use of embedded systems in the future. This is secondary application development! F...
tongchgen Embedded System
Is it necessary to add pull-up resistors to I2C devices?
Recently, I looked at some circuit diagrams about AT24C02 and found that some of them have 4.4K or 10K pull-up resistors on the SDA and SCL pins. Some do not have pull-up resistors. According to the d...
tiankai001 MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 266  1698  2219  206  2186  6  35  45  5  15 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号