The ASM3P2780A uses the most efficient and optimized
modulation profile approved by the FCC and is
implemented by using a proprietary all digital method.
The ASM3P2780A modulates the output of a single PLL
in order to “spread” the bandwidth of a synthesized clock,
and more importantly, decreases the peak amplitudes of
its harmonics. This results in significantly lower system
EMI compared to the typical narrow band signal produced
by oscillators and most frequency generators. Lowering
EMI by increasing a signal’s bandwidth is called ‘spread
spectrum clock generation’.
Generates an EMI optimized clock signal at the
output.
Integrated loop filter components.
Operates with a 3.3 / 2.5V Supply.
Operating current less than 5mA.
Low power CMOS design.
Input frequency range: 30MHz to 50MHz for 2.5V.
: 30MHz to 50MHz for 3.3V.
Generates a 1X low EMI spread spectrum clock of
the input frequency.
Frequency deviation: ±0.75% (Typ) @46MHz
Input Frequency.
Available in 6 pin TSOT-23, 8 pin SOIC and 8 pin
TSSOP Packages.
Applications
The ASM3P2780A is targeted towards all portable
devices with very low power requirements like MP3
players and digital still cameras.
Product Description
The ASM3P2780A is a versatile spread spectrum
frequency modulator designed specifically for a wide
range of clock frequencies. The ASM3P2780A reduces
electromagnetic interference (EMI) at the clock source,
allowing system wide reduction of EMI of
all clock
dependent signals. The ASM3P2780A allows significant
system cost savings by reducing the number of circuit
board layers ferrite beads, shielding that are traditionally
required to pass EMI regulations.
Key Specifications
Description
Supply voltages
Cycle-to-Cycle Jitter
Output Duty Cycle
Modulation Rate Equation
Frequency Deviation
Specification
V
DD
= 3.3V / 2.5V
200pS (Max)
45/55%
F
IN
/1280
±0.75 (Typ) @ 46MHz
Block Diagram
V
DD
PD
Modulation
XIN/CLKIN
XOUT
Crystal
Oscillator
Frequency
Divider
Feedback
Divider
Phase
Detector
Loop
Filter
PLL
VCO
Output
Divider
ModOUT
V
SS
PulseCore Semiconductor Corporation
1715 S. Bascom Ave Suite 200, Campbell, CA 95008
•
Tel: 408-879-9077
•
Fax: 408-879-9018
www.pulsecoresemi.com
Notice: The information in this document is subject to change without notice.
November
2006
rev 1.6
Pin Configuration (6-pin TSOT- 23 Package)
PD 1
XOUT 2
XIN / CLKIN 3
6 V
SS
ASM3P2780A
ASM3P2780A
5 ModOUT
4 V
DD
Pin Description
Pin#
1
2
3
4
5
6
Pin Name
PD
XOUT
XIN / CLKIN
V
DD
ModOUT
V
SS
Type
I
O
I
P
O
P
Description
Power-down control pin. Pull low to enable power-down mode. Connect to V
DD
if not
used.
Crystal connection. If using an external reference, this pin must be left unconnected.
Crystal connection or external reference frequency input. This pin has dual functions. It
can be connected either to an external crystal or an external reference clock.
Power supply for the entire chip.
Spread spectrum clock output.
Ground connection.
Pin Configuration (8-pin SOIC and TSSOP Packages)
XIN / CLKIN
1
XOUT
2
PD
NC
3
4
8
7
6
5
V
DD
NC
ModOUT
V
SS
ASM3P2780A
Pin Description
Pin#
1
2
3
4
5
6
7
8
Pin Name
XIN/CLKIN
XOUT
PD
NC
V
SS
ModOUT
NC
V
DD
Type
I
O
I
-
P
O
-
P
Description
Crystal connection or external reference frequency input. This pin has dual functions. It
can be connected either to an external crystal or an external reference clock.
Crystal connection. If using an external reference, this pin must be left unconnected.
Power-down control pin. Pull low to enable power-down mode. Connect to VDD if not
used.
No connect.
Ground connection.
Spread spectrum clock output.
No connect.
Power supply for the entire chip.
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
2 of 12
November
2006
rev 1.6
Modulation Profile
ASM3P2780A
Specifications
Description
Frequency Range
Modulation Equation
Frequency Deviation
For 2.5V Supply
For 3.3V Supply
Specification
30MHz < CLKIN < 50MHz
F
IN
/1280
±0.75% (Typ) @ 46MHz
Absolute Maximum Ratings
Symbol
V
DD
, V
IN
T
STG
T
A
T
s
T
J
T
DV
Storage temperature
Operating temperature
Max. Soldering Temperature (10 sec)
Junction Temperature
Static Discharge Voltage
(As per JEDEC STD22- A114-B)
Parameter
Voltage on any pin with respect to Ground
Rating
-0.5 to +4.6
-65 to +125
0 to 70
260
150
2
Unit
V
°C
°C
°C
°C
KV
Note: These are stress ratings only and are not implied for functional use. Exposure to absolute maximum ratings for prolonged periods of time may affect
device reliability
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
3 of 12
November
2006
rev 1.6
DC Electrical Characteristics for 2.5V Supply
(Test condition: All parameters are measured at room temperature (+25°C) unless otherwise stated)
ASM3P2780A
Symbol
V
IL
V
IH
I
IL
I
IH
I
XOL
I
XOH
V
OL
V
OH
I
DD
I
CC
V
DD
t
ON
Z
OUT
Input low voltage
Input high voltage
Input low current
Input high current
Parameter
Min
V
SS
- 0.3
2.0
-
-
-
-
-
1.8
-
-
2.375
-
-
Typ
-
-
-
-
3
3
-
-
-
4.0
2.5
-
50
Max
0.8
V
DD
+ 0.3
-35
35
-
-
0.6
-
10
-
2.625
5
-
Unit
V
V
µA
µA
mA
mA
V
V
uA
mA
V
mS
Ω
XOUT output low current (@0.6V, V
DD
=2.5V)
XOUT output high current (@1.8V, V
DD
=2.5V)
Output low voltage (V
DD
= 2.5 V, I
OL
= 8mA)
Output high voltage (V
DD
= 2.5 V, I
OH
= 8mA)
Static supply current*
Dynamic supply current (2.5V, 46MHz and no load)
Operating Voltage
Power-up time (first locked cycle after power-up)**
Output impedance
* XIN /CLKIN pin and PD pin are pulled low
** V
DD
and XIN/CLKIN input are stable, PD pin is made high from low.
AC Electrical Characteristics for 2.5V Supply
Symbol
CLKIN
ModOUT
f
d
t
LH
*
t
HL
*
t
JC
t
D
Input frequency
Output frequency
Frequency Deviation
Input Frequency = 30MHz
Input Frequency = 50MHz
Parameter
Min
30
30
-
-
0.7
0.4
-
45
Typ
-
-
± 1.10
± 0.65
1.3
0.8
-
50
Max
50
50
-
-
1.6
1.0
200
55
Unit
MHz
MHz
%
nS
nS
pS
%
Output rise time (measured from 0.7V to 1.7V)
Output fall time (measured from 1.7V to 0.7V)
Jitter (cycle to cycle)
Output duty cycle
* t
LH
and t
HL
are measured into a capacitive load of 15pF
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
4 of 12
November
2006
rev 1.6
DC Electrical Characteristics for 3.3V Supply
(Test condition: All parameters are measured at room temperature (+ 25°C) unless otherwise stated)
ASM3P2780A
Symbol
V
IL
V
IH
I
IL
I
IH
I
XOL
I
XOH
V
OL
V
OH
I
DD
I
CC
V
DD
t
ON
Z
OUT
Input low voltage
Input high voltage
Input low current
Input high current
Parameter
Min
V
SS
- 0.3
2.0
-
-
-
-
-
2.5
-
-
2.7
-
-
Typ
-
-
-
-
3
3
-
-
-
5.0
3.3
-
45
Max
0.8
V
DD
+ 0.3
-35
35
-
-
0.4
-
10
-
3.6
5
-
Unit
V
V
µA
µA
mA
mA
V
V
uA
mA
V
mS
Ω
XOUT output low current (@0.4V, V
DD
=3.3V)
XOUT output high current (@2.5V, V
DD
=3.3V)
Output low voltage (V
DD
= 3.3 V, I
OL
= 8mA)
Output high voltage (V
DD
= 3.3 V, I
OH
= 8mA)
Static supply current*
Dynamic supply current (3.3V, 46MHz and no load)
Operating Voltage
Power-up time (first locked cycle after power-up)**
Output impedance
* XIN /CLKIN pin and PD pin are pulled low
** V
DD
and XIN/CLKIN input are stable, PD pin is made high from low.
AC Electrical Characteristics for 3.3V Supply
Symbol
CLKIN
ModOUT
f
d
t
LH
*
t
HL
*
t
JC
t
D
Input frequency
Output frequency
Frequency Deviation
Input Frequency = 30MHz
Input Frequency = 50MHz
Parameter
Min
30
30
-
-
0.5
0.3
-
45
Typ
-
-
±1.10
± 0.65
1.1
0.8
-
50
Max
50
50
-
-
1.4
1.1
200
55
Unit
MHz
MHz
%
nS
nS
pS
%
Output rise time (measured from 0.8 to 2.0V)
Output fall time (measured at 2.0V to 0.8V)
Jitter (cycle to cycle)
Output duty cycle
*t
LH
and t
HL
are measured into a capacitive load of 15pF
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
Power supply: DC 27V ,400A Purpose: to charge the capacitor, the capacitance is: 100u/1000V My idea: Make a 27V oscillator to generate sinusoidal AC voltage, use a transformer to boost the voltage, th...
Hey, I've been reading the information for a long time, but I don't understand why the results are always different from what I expected. Please help me, experts...
2012 ARM Embedded Development and Application Seminar, PDF materials, the morning is an introduction to the ARM ecological environment system, and the afternoon is an introduction to Freescale, NXP, S...
In Windows XP, I performed two operations on the same file in a USB flash drive: 1. Copy the file to the hard disk; 2. Delete the file in the USB flash drive. The Windows prompt time is: 55 seconds fo...
There are many different ways of human-computer interaction. The more common ones are listed below:
Mouse interaction: Using a mouse to operate a computer and interact was the most common human...[Details]
A line scan lens is an industrial lens used with line scan cameras. Its imaging principle is to capture the image of the workpiece using a linear sensor and then perform digital signal processing t...[Details]
In recent years, the government has increasingly supported electric vehicles, and the number of electric vehicles has increased. Observant drivers will notice that there are many more green license...[Details]
For healthcare professionals, accurate diagnosis and treatment are crucial for a clear picture of a person's health. However, healthcare professionals often rely on tests at medical facilities, cli...[Details]
Gross profit margin jumped from 13.6% in the first half of last year to 25.9%, almost doubling year-on-year.
On August 21, RoboSense released its interim performance report, in which the...[Details]
Common Mode Semiconductor has officially released its latest generation of power management ICs—the GM6506 series. This fully integrated high-frequency synchronous rectification step-down p...[Details]
On August 22, South Korean media Nate reported on the 20th local time that Samsung Electronics is introducing Hyper Cell technology into its most advanced 2nm process technology, striving to improv...[Details]
As the scale and business applications of national e-government networks continue to expand, the data and services transmitted over them are becoming increasingly sensitive and critical. To protect...[Details]
With the rapid development of electric vehicles in my country, people are beginning to pay attention to the issue of radiation from electric vehicles. We all know that mobile phones emit radiation,...[Details]
Normally, we determine our location and where we want to go by comparing our surroundings with observation and simple GPS tools. However, this kind of reasoning is very difficult for self-driving c...[Details]
UPS stands for Uninterruptible Power Supply, which includes energy storage devices. It is mainly used to provide uninterruptible power supply for devices that require high power stability.
...[Details]
Based on the commutation technology, thyristor rectifiers are classified into two main types. Line-commutated and force-commutated inverters are commonly used, while other commutated inverters, nam...[Details]
PowiGaN achieves 95% efficiency at both light and full loads, meeting critical operational and safety requirements.
DARWIN, Australia and SAN JOSE, Calif.,
August 22, 2025 – Powe...[Details]
Compared to cloud databases, minicomputers are purpose-built for decentralized, rugged computing at the edge of the network. By moving applications, analytics, and processing services closer to the...[Details]
According to Nikkei, a survey found that global electric vehicle battery supply is expected to reach more than three times the required quantity due to
cooling
demand for electric vehicles,...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
