The ASM3P2780A uses the most efficient and optimized
modulation profile approved by the FCC and is
implemented by using a proprietary all digital method.
The ASM3P2780A modulates the output of a single PLL
in order to “spread” the bandwidth of a synthesized clock,
and more importantly, decreases the peak amplitudes of
its harmonics. This results in significantly lower system
EMI compared to the typical narrow band signal produced
by oscillators and most frequency generators. Lowering
EMI by increasing a signal’s bandwidth is called ‘spread
spectrum clock generation’.
Generates an EMI optimized clock signal at the
output.
Integrated loop filter components.
Operates with a 3.3 / 2.5V Supply.
Operating current less than 5mA.
Low power CMOS design.
Input frequency range: 30MHz to 50MHz for 2.5V.
: 30MHz to 50MHz for 3.3V.
Generates a 1X low EMI spread spectrum clock of
the input frequency.
Frequency deviation: ±0.75% (Typ) @46MHz
Input Frequency.
Available in 6 pin TSOT-23, 8 pin SOIC and 8 pin
TSSOP Packages.
Applications
The ASM3P2780A is targeted towards all portable
devices with very low power requirements like MP3
players and digital still cameras.
Product Description
The ASM3P2780A is a versatile spread spectrum
frequency modulator designed specifically for a wide
range of clock frequencies. The ASM3P2780A reduces
electromagnetic interference (EMI) at the clock source,
allowing system wide reduction of EMI of
all clock
dependent signals. The ASM3P2780A allows significant
system cost savings by reducing the number of circuit
board layers ferrite beads, shielding that are traditionally
required to pass EMI regulations.
Key Specifications
Description
Supply voltages
Cycle-to-Cycle Jitter
Output Duty Cycle
Modulation Rate Equation
Frequency Deviation
Specification
V
DD
= 3.3V / 2.5V
200pS (Max)
45/55%
F
IN
/1280
±0.75 (Typ) @ 46MHz
Block Diagram
V
DD
PD
Modulation
XIN/CLKIN
XOUT
Crystal
Oscillator
Frequency
Divider
Feedback
Divider
Phase
Detector
Loop
Filter
PLL
VCO
Output
Divider
ModOUT
V
SS
PulseCore Semiconductor Corporation
1715 S. Bascom Ave Suite 200, Campbell, CA 95008
•
Tel: 408-879-9077
•
Fax: 408-879-9018
www.pulsecoresemi.com
Notice: The information in this document is subject to change without notice.
November
2006
rev 1.6
Pin Configuration (6-pin TSOT- 23 Package)
PD 1
XOUT 2
XIN / CLKIN 3
6 V
SS
ASM3P2780A
ASM3P2780A
5 ModOUT
4 V
DD
Pin Description
Pin#
1
2
3
4
5
6
Pin Name
PD
XOUT
XIN / CLKIN
V
DD
ModOUT
V
SS
Type
I
O
I
P
O
P
Description
Power-down control pin. Pull low to enable power-down mode. Connect to V
DD
if not
used.
Crystal connection. If using an external reference, this pin must be left unconnected.
Crystal connection or external reference frequency input. This pin has dual functions. It
can be connected either to an external crystal or an external reference clock.
Power supply for the entire chip.
Spread spectrum clock output.
Ground connection.
Pin Configuration (8-pin SOIC and TSSOP Packages)
XIN / CLKIN
1
XOUT
2
PD
NC
3
4
8
7
6
5
V
DD
NC
ModOUT
V
SS
ASM3P2780A
Pin Description
Pin#
1
2
3
4
5
6
7
8
Pin Name
XIN/CLKIN
XOUT
PD
NC
V
SS
ModOUT
NC
V
DD
Type
I
O
I
-
P
O
-
P
Description
Crystal connection or external reference frequency input. This pin has dual functions. It
can be connected either to an external crystal or an external reference clock.
Crystal connection. If using an external reference, this pin must be left unconnected.
Power-down control pin. Pull low to enable power-down mode. Connect to VDD if not
used.
No connect.
Ground connection.
Spread spectrum clock output.
No connect.
Power supply for the entire chip.
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
2 of 12
November
2006
rev 1.6
Modulation Profile
ASM3P2780A
Specifications
Description
Frequency Range
Modulation Equation
Frequency Deviation
For 2.5V Supply
For 3.3V Supply
Specification
30MHz < CLKIN < 50MHz
F
IN
/1280
±0.75% (Typ) @ 46MHz
Absolute Maximum Ratings
Symbol
V
DD
, V
IN
T
STG
T
A
T
s
T
J
T
DV
Storage temperature
Operating temperature
Max. Soldering Temperature (10 sec)
Junction Temperature
Static Discharge Voltage
(As per JEDEC STD22- A114-B)
Parameter
Voltage on any pin with respect to Ground
Rating
-0.5 to +4.6
-65 to +125
0 to 70
260
150
2
Unit
V
°C
°C
°C
°C
KV
Note: These are stress ratings only and are not implied for functional use. Exposure to absolute maximum ratings for prolonged periods of time may affect
device reliability
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
3 of 12
November
2006
rev 1.6
DC Electrical Characteristics for 2.5V Supply
(Test condition: All parameters are measured at room temperature (+25°C) unless otherwise stated)
ASM3P2780A
Symbol
V
IL
V
IH
I
IL
I
IH
I
XOL
I
XOH
V
OL
V
OH
I
DD
I
CC
V
DD
t
ON
Z
OUT
Input low voltage
Input high voltage
Input low current
Input high current
Parameter
Min
V
SS
- 0.3
2.0
-
-
-
-
-
1.8
-
-
2.375
-
-
Typ
-
-
-
-
3
3
-
-
-
4.0
2.5
-
50
Max
0.8
V
DD
+ 0.3
-35
35
-
-
0.6
-
10
-
2.625
5
-
Unit
V
V
µA
µA
mA
mA
V
V
uA
mA
V
mS
Ω
XOUT output low current (@0.6V, V
DD
=2.5V)
XOUT output high current (@1.8V, V
DD
=2.5V)
Output low voltage (V
DD
= 2.5 V, I
OL
= 8mA)
Output high voltage (V
DD
= 2.5 V, I
OH
= 8mA)
Static supply current*
Dynamic supply current (2.5V, 46MHz and no load)
Operating Voltage
Power-up time (first locked cycle after power-up)**
Output impedance
* XIN /CLKIN pin and PD pin are pulled low
** V
DD
and XIN/CLKIN input are stable, PD pin is made high from low.
AC Electrical Characteristics for 2.5V Supply
Symbol
CLKIN
ModOUT
f
d
t
LH
*
t
HL
*
t
JC
t
D
Input frequency
Output frequency
Frequency Deviation
Input Frequency = 30MHz
Input Frequency = 50MHz
Parameter
Min
30
30
-
-
0.7
0.4
-
45
Typ
-
-
± 1.10
± 0.65
1.3
0.8
-
50
Max
50
50
-
-
1.6
1.0
200
55
Unit
MHz
MHz
%
nS
nS
pS
%
Output rise time (measured from 0.7V to 1.7V)
Output fall time (measured from 1.7V to 0.7V)
Jitter (cycle to cycle)
Output duty cycle
* t
LH
and t
HL
are measured into a capacitive load of 15pF
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
4 of 12
November
2006
rev 1.6
DC Electrical Characteristics for 3.3V Supply
(Test condition: All parameters are measured at room temperature (+ 25°C) unless otherwise stated)
ASM3P2780A
Symbol
V
IL
V
IH
I
IL
I
IH
I
XOL
I
XOH
V
OL
V
OH
I
DD
I
CC
V
DD
t
ON
Z
OUT
Input low voltage
Input high voltage
Input low current
Input high current
Parameter
Min
V
SS
- 0.3
2.0
-
-
-
-
-
2.5
-
-
2.7
-
-
Typ
-
-
-
-
3
3
-
-
-
5.0
3.3
-
45
Max
0.8
V
DD
+ 0.3
-35
35
-
-
0.4
-
10
-
3.6
5
-
Unit
V
V
µA
µA
mA
mA
V
V
uA
mA
V
mS
Ω
XOUT output low current (@0.4V, V
DD
=3.3V)
XOUT output high current (@2.5V, V
DD
=3.3V)
Output low voltage (V
DD
= 3.3 V, I
OL
= 8mA)
Output high voltage (V
DD
= 3.3 V, I
OH
= 8mA)
Static supply current*
Dynamic supply current (3.3V, 46MHz and no load)
Operating Voltage
Power-up time (first locked cycle after power-up)**
Output impedance
* XIN /CLKIN pin and PD pin are pulled low
** V
DD
and XIN/CLKIN input are stable, PD pin is made high from low.
AC Electrical Characteristics for 3.3V Supply
Symbol
CLKIN
ModOUT
f
d
t
LH
*
t
HL
*
t
JC
t
D
Input frequency
Output frequency
Frequency Deviation
Input Frequency = 30MHz
Input Frequency = 50MHz
Parameter
Min
30
30
-
-
0.5
0.3
-
45
Typ
-
-
±1.10
± 0.65
1.1
0.8
-
50
Max
50
50
-
-
1.4
1.1
200
55
Unit
MHz
MHz
%
nS
nS
pS
%
Output rise time (measured from 0.8 to 2.0V)
Output fall time (measured at 2.0V to 0.8V)
Jitter (cycle to cycle)
Output duty cycle
*t
LH
and t
HL
are measured into a capacitive load of 15pF
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
Live Topic: Microchip Live | ADAS Platform Root of TrustContent Introduction: Computers and other software-driven products have become integrated into almost every aspect of modern life. Even the cars...
Source code link [url=https://download.eeworld.com.cn/user/sogaside]https://download.eeworld.com.cn/user/sogaside[/url] Source code on github is here [url=https://github.com/sogaside/sensortile]https:...
StartFragmentWhen adding assembly language to the software, for example: asm(" ldf @_ftemp_com,r0 "); asm(" ldi @constdata_add,ar1 "); a warning message is displayed saying function "asm" declared imp...
I am a beginner in single-chip microcomputer. I recently soldered an AT89C2051 minimum system and used Keil to write a small program to control the flashing of the light. However, there was no respons...
[size=6][backcolor=rgb(239, 245, 249)]Brand new original chips!!! [/backcolor][/size][size=6][backcolor=rgb(239, 245, 249)]Some are in the original package, and some are only used 1-2. Here is the lis...
1. Equipment Overview
Shell-and-tube heat exchangers are a common heat exchange device used in chemical evaporation and heating equipment. Currently, the tubesheets of shell-and-tube heat exch...[Details]
Tesla and BYD, vying for dominance in the global electric vehicle market, are reportedly considering adopting Samsung's AMOLED (active-matrix organic light-emitting diode) technology for their next...[Details]
introduction
With the development of digital and network technologies, broadcasting technology has become increasingly diversified, with the most significant trend being the transition from an...[Details]
"Have you set your calendar reminder?"
On August 24, Nvidia Robotics' official account posted a photo of a black gift box on a social media platform, with an attached greeting card sig...[Details]
As the main model among new energy vehicles, pure electric vehicles have received strong support and encouragement from the country in recent years, and their development is changing with each pass...[Details]
The most significant feature of IPS panels is that both electrodes are located on the same surface, unlike other LCD panels, which have electrodes arranged on top and bottom surfaces in a three-dim...[Details]
Limited vocabulary recognition
According to the number of characters, words or short sentences in the vocabulary, it can be roughly divided into: less than 100 is small vocabulary; 100-1000 is...[Details]
Introduction to the principles of speech recognition technology
Automatic speech recognition (ASR) technology aims to enable computers to understand human speech and extract the textual inform...[Details]
Since its invention in the mid-1940s, the microwave oven has evolved from a humble beginning to commercial use, entering homes in the 1960s and rapidly gaining popularity. Its basic functionality a...[Details]
1. Multi-channel DAC technology bottleneck
Currently,
the development of multi-channel DAC technology focuses on two core challenges.
First, industrial applications urgently ...[Details]
Reflow soldering is one of the most commonly used methods in electronics manufacturing, allowing for the soldering of large numbers of components in a relatively short time. However, any experience...[Details]
We often hear about the precautions for using pure electric vehicles in winter, and many owners even develop relevant strategies, such as adopting a "charge as you go" principle for their vehicles,...[Details]
As the range of electric vehicles continues to increase, driving electric vehicles for long-distance travel has become a trend. For high-speed travel, how much impact will high-speed driving of ele...[Details]
With the support and encouragement of national policies, some Internet car manufacturers have also joined the new energy vehicle manufacturing industry. From the perspective of new car manufacturer...[Details]
With growing environmental awareness, the continuous improvement of three-electric technology and the increasing deployment of infrastructure such as charging stations, the electrification of new e...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
