As shown in the two pictures below, the first method is to use a bend to make up for the equal length error of the differential lines. The second method is to slightly increase the spacing between the...
Is there any senior who knows about the stcstc89c52rc microcontroller? I am learning it myself. If you have any information on learning microcontroller programming, please share it with me. Thank you...
[i=s]This post was last edited by fish001 on 2019-8-8 22:51[/i]I didn't use Keil, I used IAR.
The MCU source code is as follows:#include msp430f5529.h#include "SPI.h"#include "MAX7456.h"
#define uint ...
In the previous chapters (Signals and Slots and Custom Signals and Slots), we introduced the new syntax of signals and slots in Qt 5 in detail. Since this change is large, many problems that did not s...
Dear experts, I am eager to find the AT91SAM7S64 evaluation board routine. I hope some friends can send it to me. Thank you very much:):), or send it to my email [url=mailto:whwshiyuan@126.com]whwshiy...
Example PurposeDemonstrates the use of AT32F4xx_CAN filter. The filter is mainly used to selectively receive messages.
Supported models:AT32F403xxAT32F403AxxAT32F407xxAT32F413xxAT32F415xx
Main periphe...
The Wassenaar Arrangement, everything started during the Cold War. Let's learn more about it with the embedded editor.
background
After the end of World War II, the United States ...[Details]
According to foreign media reports, the 2018 GMC Terrain Denali is equipped with multiple collision detection systems, and a recent test verified the safety of the system. Even when driving in a bu...[Details]
1. Introduction to MC68K CPU The MC683xx series of microcontrollers are composed of the famous MOTOROLA 32-bit microprocessors such as MC68K, 68020, 68040, and the compatible 68K, CPU32, CPU3...[Details]
The analog watchdog of the ADC is used to check if the voltage is out of bounds. It has two upper and lower bounds, which can be set in the registers ADC_HTR and ADC_LTR respectively. The library fun...[Details]
T1 or T2 are two timers/counters of MCS-51 microcontroller. The first method can use two timers/counters to generate rectangular waves. In order to save interface resources, the second method is used...[Details]
The single-chip microcomputer running light program requires all 32 serial ports to be used, and each serial port has eight LEDs. Question supplement: The 8051 single-chip microcomputer is used, an...[Details]
Manually assemble the following program machine code and analyze the execution function of the program segment. CLR A MOV R2, A MOV R7, #4 LOOP: CLR C MOV A, R0 RLC...[Details]
A simple experimental programming question for the microcontroller: write a 3-byte binary addition subroutine. The program entry is: addend 1: 22H, 21H, 20H three bytes, 22H is the highest bit; adden...[Details]
It is required to use timer/counter 1 for timing, with a timing of 1 second; timer/counter 0 for counter, and the external pulse to be counted is connected from P3.4 (T0). The microcontroller will co...[Details]
The following comes from - "cortex-M3 Definitive Guide" Special function register group: Program Status Registers (PSRs or xPSRs) Interrupt mask register group (PRIMASK, FAULTMASK, and BASEPRI) ...[Details]
I have been working on single-chip microcomputers for several years, and I have always wanted to make a series of summaries. It happened to rain today. As the saying goes: Rainy days are good for...[Details]
1. Pin: 0 in 1 out Set Status Output status IO register setting DDR×A certain bit is set to 1, and the corresponding bit IO is set to output; PORT×A certain position is 1/0, and t...[Details]
After three years of continuous decline in its mobile phone business, ZTE has finally revealed its true feelings to the outside world: the Chinese market is its weak point, and it is planning to f...[Details]
PCB Design
京公网安备 11010802033920号
EEWORLD
