EEWORLDEEWORLDEEWORLD

Part Number

Search

PTN2512K1522BGT5

Description
RESISTOR, THIN FILM, 1 W, 0.1 %, 100 ppm, 15200 ohm, SURFACE MOUNT, 2512, CHIP, ROHS COMPLIANT
CategoryPassive components    The resistor   
File Size117KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance  
Download Datasheet Parametric View All

PTN2512K1522BGT5 Overview

RESISTOR, THIN FILM, 1 W, 0.1 %, 100 ppm, 15200 ohm, SURFACE MOUNT, 2512, CHIP, ROHS COMPLIANT

PTN2512K1522BGT5 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerVishay
package instructionSMT, 2512
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresANTI-SULFUR; LASER TRIMMABLE; NON-INDUCTIVE
structureRectangular
JESD-609 codee4
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.838 mm
Package length6.579 mm
Package formSMT
Package width3.15 mm
method of packingTR
Rated power dissipation(P)2 W
Rated temperature70 °C
resistance15200 Ω
Resistor typeFIXED RESISTOR
size code2512
surface mountYES
technologyTHIN FILM
Temperature Coefficient100 ppm/°C
Terminal surfaceGold (Au) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage200 V
PTN
Vishay Thin Film
Commercial Thin Film Chip Resistors
FEATURES
Lead (Pb)-free or Sn/Pb terminations available
Pb-free
Moisture resistant
Available
High purity alumina substrate
RoHS*
Non-standard values available
COMPLIANT
Will pass + 85 °C, 85 % relative humidity and
10 % rated power
100 % visual inspected per MIL-PRF-55342
Very low noise and voltage coefficient (< - 30 dB)
Non-inductive
Laser-trimmed tolerances to ± 0.1 %
Wraparound resistance less than 10 mΩ
Epoxy bondable termination available
Actual Size
1505
SURFACE MOUNT
CHIPS
These chip resistors are available in both “top side” and
“wraparound” termination styles in a variety of sizes. They
incorporate self passivated, enhanced Tantalum Nitride
films, to give superior performance on moisture resistance,
voltage coefficient, power handling and resistance stability.
The terminations consist of an adhesion layer, a leach
resistant nickel barrier, and solder coating. This product will
out-perform all requirements of characteristic H of
MIL-PRF-55342.
CONSTRUCTION
Passivation
Tantalum
Nitride
Resistive Film
Solder
coating
Nickel barrier
High Purity
Alumina Substrate
Adhesion layer
TYPICAL PERFORMANCE
ABS
TCR
TOL
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Absolute TCR
Absolute Tolerance
Operating Temperature Range
Noise
CASE SIZE
0402
0502
0505
0603
0805
(1)
, 0705
(1)
1005
1010
1206
1505
2208
2010
2512
POWER RATING (mW)
50
100
150
150
200
250
500
400
400
750
800
1000
SPECIFICATIONS
Tantalum nitride
± 25 ppm/°C, ± 50 ppm/°C, ± 100 ppm/°C
± 1.0 %, ± 0.5 % and ± 0.1 %
- 55 °C to + 125 °C
< - 25 dB
MAX. WORKING VOLTAGE
75
75
75
75
100
100
150
200
150
150
200
200
RESISTANCE RANGE - (Ω)
20 - 35K
20 - 65K
20 - 130K
10 - 80K
10 - 301K
10 - 301K
50 - 600K
10 - 1M
10 - 1M
10 - 1.75M
10 - 2M
10 - 3M
- 55 °C to + 125 °C
+ 25 °C
CONDITIONS
Note
(1)
0705 and 0805 are the same (only use 0805 when ordering)
* Pb containing terminations are not RoHS compliant, exemptions may apply
Document Number: 60026
Revision: 23-Jan-09
For technical questions, contact: thin-film@vishay.com
www.vishay.com
55
Cisco was reported to have laid off employees in China, and the average compensation for laid-off employees was more than 1 million
Today, there is news that Cisco's RD department in Shanghai has laid off employees. There is also a clarification that it is a department in Shanghai that was laid off because the product of outdoor f...
eric_wang Talking
How to build and run the RFID design platform
1. Prepare the design platform environment Use the ULINK2 emulator to connect the JTAG interface of the motherboard of the EduKit-IV experimental design platform; use the cross serial cable that comes...
Jacktang RF/Wirelessly
Is BCM5318 discontinued?
As the title[:)]...
guangzhouzxz RF/Wirelessly
430 and reset chip, the system freezes, please help
[color=#000][backcolor=rgb(232, 232, 232)][size=15px]During the test, 430 used 149 chips, and the reset chip used TPS3823. The purpose of the test was to see the accuracy of the external watchdog. The...
hanwenli123 Microcontroller MCU
How to burn the program of LM3S2110 board? Thanks to all the masters!!TT
The EK kit that comes with the 8962 has 10-pin CAN and 20-pin debug, but no USB port. What to do?...
dove0413 Microcontroller MCU
AFA Secret 3: Those who boast about the highest performance are just hooligans
Reposted from [url]http://mp.weixin.qq.com/s?__biz=MzAwMDM4NTUyNw==&mid=402889857&idx=1&sn=d1ff6c8254423c62361dd2ae016496d3&3rd=MzA3MDU4NTYzMw==&scene=6#rd[/url]Nowadays, many manufacturers are proud ...
白丁 FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 481  38  732  1752  2674  10  1  15  36  54 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号