EEWORLDEEWORLDEEWORLD

Part Number

Search

SS016M0022B2F-0407

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 16V, 20% +Tol, 20% -Tol, 22uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size58KB,2 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance  
Download Datasheet Parametric View All

SS016M0022B2F-0407 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 16V, 20% +Tol, 20% -Tol, 22uF, Through Hole Mount, ROHS COMPLIANT

SS016M0022B2F-0407 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompli
ECCN codeEAR99
capacitance22 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
leakage current0.00352 mA
Manufacturer's serial numberSS
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingBULK
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)16 V
ripple current44 mA
surface mountNO
Delta tangent0.17
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
Miniature Size Aluminum
Electrolytic Capacitors
SS
[ For Super Miniature ]
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40° ~ +105°C
Working Voltage : 6.3 ~ 80V
Rate Capacitance Range : 0.1 ~ 470µF
Capacitance Tolerance : -20 ~ +20%
DC Leakage Current (µA) : I = 0.01CV (µA) or 3µA Whichever is greater.
DESCRIPTION
This type is designed to meet the demand or
equipments for greatly reduced size and thickness,
such as: portable micro computer, disk driver, small
calculator and audio equipement.
( After 2 Minutes Application of DC Working Voltage at 25°C )
Dissipation Factor : at 120 Hz, 25°C
W V (V) : 6.3
D.F (%) : 24
10
20
16
17
25
15
35
12
50
10
63
8
80
8
Load Life : 1000 Hours at 105°C Assured with Full Rated Maximum Ripple Current Applied
Application :
Portable Micro Computer,
Disk Driver,
Small Calculator and Audio
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : 500 Hours, No Voltage Applied, at 105°C
Multiplier for Ripple Current
Frequency (Hz)
0.1~47µF
100~330µF
50
0.75
0.75
120
1.00
1.00
300
1.20
1.10
1K
1.30
1.15
10K
1.50
1.20
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
Temperature(°C)
Factor
65
1.70
85
1.30
105
1.00
Dimensions : mm
Rubber Stand-off
DIAGRAM OF DIMENSIONS
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
Rubber End Seal
F 0.5
F
1.5
2.0
2.5
3.5
0.45
F 0.5
0.4Max.
15Min.
4.0
5.0
L
15Min.
5Min.
D 0.5
L
5Min.
D 0.5
6.3
8.0
0.5
Matrix keyboard problem, can't be fixed
A simple 2*8 matrix keyboard is shown in the picture. I have been struggling with it for a day but still can't figure it out. Does anyone have any suggestions?I configured it as follows:GPIO_InitStruc...
cclinyes stm32/stm8
Problems loading libACE.so on VxWorks simulator
Dear experts: According to the documentation of NT host VxWorks Target, libACE.so and libTAO.so files have been successfully generated. However, when executing ldld < libACE.out undefined symbol: _unl...
天天 Real-time operating system RTOS
EEWORLD University - Start learning from TI Bluetooth solutions
Start learning from TI Bluetooth solutions : https://training.eeworld.com.cn/course/412...
chenyy RF/Wirelessly
Why does the same error occur when compiling the driver?
When I recently compiled a Linux driver for PXA270, the following prompt appeared: ERROR: Kernel configuration is invalid. include/linux/autoconf.h or include/config/auto.conf are missing. Run 'make o...
leungpki Embedded System
~~~~~~Beautiful flight path~~~~~~
Although this is a masterpiece of jet engines and nature, in the final analysis, it is still the pride of MG[[i] This post was last edited by zcgzanne on 2010-2-11 20:33 [/i]]...
zcgzanne Talking
PCB board grinding process
Grinding is an auxiliary process that may be used many times in the PCB manufacturing process. As a pre-treatment or post-treatment process of other processes, the PCB board is generally first pickled...
ESD技术咨询 PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1271  895  209  2785  2351  26  19  5  57  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号