As the title says, I am debugging the native USB of 28377. I run the routine in controlSUIT and can identify an unknown USB device after connecting to the Windows computer. I know that I need to insta...
I have a launchpad and an AD7416 temperature sensor, but I'm not very good at programming. Is there anyone who has done this before? Please help me post the program! ! ! !...
This year, I participated in the Freescale Smart Car Competition. The board was officially donated to our school. I searched online for information about the MC9S12XS128 microcontroller. Most of the i...
How to control the speed of the LED light on and off at the FPGA end through DSP? As the title says, I recently encountered a difficulty, which is to control the frequency of the LED light on and off ...
[b][color=#0000ff]I. Fill in the blanks[/color][/b] 1. The interconnection lines on the PCB can be divided into () and () by type. 2. The two factors that cause crosstalk are () and (). 3. The three e...
It has been so many days and the goods have not been shipped yet. The status is "[color=#555555][font="][size=15px]In Work at Fulfillment". Has anyone encountered this situation? [/size][/font][/color...
Dong Yang, executive vice president of the China Association of Automobile Manufacturers, said on the 26th that according to the authorization of the Ministry of Industry and Information Technology...[Details]
China's photovoltaic power generation installed capacity achieved rapid growth in 2017, and distributed photovoltaics achieved explosive growth. In 2017, the country's photovoltaic installed capaci...[Details]
Recently, the results of the 2018 German Red Dot Design Award were announced. GoodWe, a company located in Suzhou High-tech Zone, stood out among thousands of outstanding design products from 5...[Details]
1. Principle 1. Infrared emission protocol There are many infrared communication protocols. This experiment uses the NEC protocol. This protocol uses PWM modulation and uses pulse width to represen...[Details]
1. Placement suspension void NVIC_Configuration(void) { NVIC_InitTypeDef NVIC_InitStructure; /* Set the Vector Table base location at 0x08004000 NVIC_SetVectorTable(NVIC_VectTab_FLASH, 0x4000)...[Details]
In the previous article, I wrote a simple GPIO running light test, which looked a bit monotonous. I was used to serial port debugging. If there was no serial port on the board, I had to find another ...[Details]
The day before yesterday, I learned about STM's Systick and found it quite useful for precise timing. When I used CVAVR before, I found that the delay.h in it was very useful. So, I used STM32's...[Details]
Friends who work in the photovoltaic industry, do you still remember the hard work on June 30 last year? How many people worked late into the night for months in a row just to connect to the grid a...[Details]
Today, under the guidance of a low-level expert, I learned how to configure the PWM module! Woof! First open the file configured last time, as follows: Then, we need to use TIM1 to set PWM: Then,...[Details]
introduction STM32 has many registers, which are difficult to remember, so the official packaged two sets of library functions. One is the standard library, but the official has not updated it on F7,...[Details]
introduction In the general project development process, two or more microcontrollers are often required to communicate to complete data transmission. For example, a quadcopter wirelessly transmits d...[Details]
Serial Port: 一. USART_ITConfig(USART1, USART_IT_TXE, ENABLE): As long as the transmit register is empty, there will always be an interrupt. Therefore, if you are not sending data, turn off the tran...[Details]
In 1952, Bell Labs built a 6-foot-tall automatic number recognition machine called "Audrey", which could recognize the pronunciation of the numbers 0 to 9 with an accuracy of more than 90%. And its...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
