Environment: AT91Rm9200 +S29Gl064A R6 SDRAM MT48LC16 U-boot +linux system Problem: After the board is booted from the internal rom, the uboot can be downloaded through commands and write data to the f...
Project description: 1. Using chip HT82M99E 2. Purpose: simulate keyboard, upload small amount of data to PC. 3. All products have the same VID and PID. Problem description: 1. Assume there are two HI...
Dear friends who have supported this tutorial, I am sorry to inform you that there will be no more tutorials from this issue. Because I am about to start looking for a job. Thank you for your continue...
Finally I have time to calm down and learn about 5969, but I hit a wall at the beginning. The official programming method of 5969 is based on library operation, which is really not accustomed to, but ...
Wang Xiaochuan, the "Wudaokou Goalkeeper", is going through a level that he has never gone through before. For example, Sogou's (NYSE: SOGO) financial report, artificial intelligence, and the futur...[Details]
International Solar Photovoltaic Network News: Chinese inverter company Sungrow announced that it will build a 3GW photovoltaic inverter manufacturing plant in Bangalore, the capital of Karnataka, ...[Details]
In 2017,
Sanan Optoelectronics
achieved sales revenue of 8.394 billion yuan, operating profit of 3.856 billion yuan, and net profit attributable to shareholders of the parent company of 3.1...[Details]
After searching a lot of information, I finally understood the time base timer. I did not use any library functions but operated the registers directly. The following introduces the systick in STM32...[Details]
Using Systick timer to achieve delay 1. SysTick timer characteristics The SysTick timer is a 24-bit down counter, that is, when vlue is decremented to 0, an interrupt is triggered and the load va...[Details]
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
I used STM32CubeMX V4.22.1 to generate a project including EHT and Lwip. The debugging has been abnormal. After careful inspection, the following problems were found: 1. The hardware uses LAN8720A, b...[Details]
In 2018, the National Development and Reform Commission issued a new photovoltaic subsidy policy. The benchmark on-grid electricity price was significantly reduced, the return on investment decreased,...[Details]
STM32 has three startup modes. In RM0008 downloaded from the ST official website, you can find the startup-related configuration instructions: Translated into Chinese: The storage media corresp...[Details]
If you do not use an external crystal on the STM32, the connection method of OSC_IN and OSC_OUT If you use the internal RC oscillator instead of an external crystal, please follow the following metho...[Details]
ADC: 1. The ADC module inside STM32 has three ADC1, ADC2, and ADC3, which are independent of each other, so synchronous sampling can be performed. 2ADC input clock must not exceed 14MHz, it is genera...[Details]
The key is the configuration of registers. The T1 timer (16 bits) of CC2530 needs to configure three registers: T1CTL, T1STAT, IRCON Here is just a brief introduction. For more details, please refer ...[Details]
T1 or T2 are two timers/counters of MCS-51 microcontroller. The first method can use two timers/counters to generate rectangular waves. In order to save interface resources, the second method is used...[Details]
MCS-51 single-chip microcomputer timer/counter experiment programming program Programming requirements: 1. Connect a light-emitting diode LED to the P1.0 pin, light up for two seconds, turn off for o...[Details]
(1) JTAG is a communication standard used for real-time and fast communication between computers and microcontrollers. The JTAG function of AVR (only available on some models) makes AVR debugging ver...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
