^For symbol “U” termination add .20 inches (0.51mm) to the positive length tolerance and .015 inches (0.38mm) to the positive width and thickness tolerances.
Ordering Information
03028
DSCC Drawing
Number
03028 (0603 case size)
BX
Dielectric
BR
BX
104
Capacitance
Code (pF)
2 Sig. Digits +
Number of
Zeros
Y
Voltage
W = 6.3V
X = 10V
Y = 16V
Z = 25V
A = 50V
B = 100V
C = 200V
J
Capacitance
Tolerance
J = ±5%
K = ±10%
M = ±20%
Z
End
Metallization^
U = SnPb (4% min)
Z = SnPb (4% min)
C
Group C
Testing Option
Blank = No group C testing
C = Full group C
L = 2,000 hour life test only
M = 1,000 hour life test only
H = Low voltage humidity only
7189
Packaging/Grade
(C-Spec)*
Blank = Waffle Pack
7189 = 7” Reel
^ “U” = Base metallization-barrier metal-solder coated (tin/lead alloy, with a min of 4% lead). Melting point is +200ºC or less. Metallization thickness is
≥
60μ-inches.
^ “Z” = Base metallization-barrier metal-tinned (tin/lead alloy, with a min of 4% lead).
* Additional reeling or packaging options may be available. Contact KEMET for details.
Additional termination options may be available. Contact KEMET for details.
What do you need for your next embedded system design project: a flexible system component that allows you to easily customize the design, or extra performance headroom so that you can add more functi...
After a whole afternoon of tinkering, I ran all the peripherals that might be used.Basically, they are GPIO, timers, serial ports, buttons, etc.I will also find examples to play with AD.1. LEDis very ...
[i=s] This post was last edited by elec32156 on 2017-11-3 10:04 [/i] As shown in the figure, it is the parameter specification of the light sensor. Different currents are output under different lighti...
[backcolor=rgb(238, 238, 238)][size=14px][font=Tahoma, Helvetica, SimSun, sans-serif][size=12px]I saw an article on the Internet, and excerpted an interesting passage: [/size][/font][/size][/backcolor...
There are two PCBs in the 86 box, one is the display board and the other is the peripheral control board. The two boards are connected by FCC10_1.0 cable, and the cable definition is: 5V PPWM2 PPWM1 P...
introduction
1 The significance of using RTOS on MSP430
It is understandable that it is meaningless to use RTOS on MSP430. Because the hardware resources of MSP430 are limited (for exampl...[Details]
1. Introduction
RFID (radio frequency identification) is a non-contact automatic identification technology that emerged in the 1990s. It uses the characteristics of radio frequency signal prop...[Details]
Analog engineers have traditionally struggled with complexity when designing power supplies that required multiple outputs, dynamic load sharing, hot-swap, or extensive fault-handling capabilities....[Details]
The reason for the light decay of white LEDs: the decline of phosphor performance
So far, the rapid decline of the luminous performance of white light LEDs, especially low-power white light LE...[Details]
Electronic systems are located at different points on the automotive power bus and therefore often need to operate under very stringent power requirements. These include load dump, cold crank, very lo...[Details]
1 Introduction
Intelligent control instruments are one of the most commonly used controllers in industrial control. They are mainly aimed at a specific parameter (such as pressure, tempera...[Details]
1. Introduction
Testing the temperature of steel billets before rolling is an important measure to ensure the quality of steel. Traditional manual testing is difficult to ensure product qu...[Details]
On the afternoon of July 10, Beijing time, Taiwan's largest chip designer MediaTek expects its smartphone chip shipments to grow by double digits in the third quarter of this year, and the company is ...[Details]
With the widespread application of new services and technologies in the communications industry, the scale and capacity of operators' network construction are getting larger and larger, and the ris...[Details]
Liquid crystal display (LCD) panels have a wide range of applications, from small portable electronic devices to large fixed devices, including digital cameras, laptops, personal data assistants, d...[Details]
The DisplayPort interface standard is approved by the Video Electronics Standards Association (VESA) to provide an open, scalable standard for the entire industry. The development of DisplayPort ca...[Details]
Analysis of the three core aspects of digital TV transmission standards
According to the differences in regionality, transmission method and modulation method, the transmission method needs to...[Details]
When the so-called "copycat phones" that flood the domestic mobile phone market move towards large screens, stereo amplifiers, touch controls, and even GPS navigation and mobile TV, the homogeneity...[Details]
1 Introduction to LED
With the development of science and technology, people have higher and higher requirements on automobile light sources. LED (Light Emitting Diode) has gradually attracted...[Details]
introduction
At present, the research on micron and nanotechnology is very active, which has led to the rapid development of microtechnology and micro-mechanical electronic system (MEMS) t...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
