performance oscillators utilize a proven silicon MEMS
technology to provide excellent jitter and stability over
a wide range of supply voltages and temperatures. By
eliminating the need for quartz or SAW technology,
MEMS oscillators significantly enhance reliability and
accelerate product development, while meeting
stringent clock performance criteria for a variety of
communications, storage, and networking applications.
DSC1101 has a standby feature that allows it to
completely power-down when EN pin is pulled low;
whereas for DSC1121, only the outputs are disabled
when EN is low. Both oscillators are available in
industry standard packages, including the small
2.5 mm x 2.0 mm, and are “drop-in” replacements for
standard 4-pin CMOS quartz crystal oscillators.
Functional Block Diagram
Applications
• Storage Area Networks
- SATA, SAS, Fibre Channel
• Passive Optical Networks
- EPON, 10G-EPON,V GPON, 10G-PON
• Ethernet
- 1G, 10GBASE-T/KR/LR/SR, and FCoE
• HD/SD/SDI Video and Surveillance
• PCI Express
• Display Port
2017-2019 Microchip Technology Inc.
DS20005613C-page 1
DSC1101/21
1.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings †
Input Voltage, V
IN
............................................................................................................................. –0.3V to V
DD
+ 0.3V
Supply Voltage .......................................................................................................................................... –0.3V to +4.0V
ESD Protection On All Pins ...........................................................................................4000V HBM, 1500V CDM (max.)
† Notice:
Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those indicated
in the operational sections of this specification is not intended. Exposure to maximum rating conditions for extended
periods may affect device reliability.
Note:
1000+ years of data retention on internal memory.
DC CHARACTERISTICS
Electrical Characteristics
Parameters
Supply Voltage (Note
1)
Sym.
V
DD
Min.
2.25
—
Supply Current
I
DD
—
—
Frequency Stability
(Including frequency
variations due to initial
tolerance, temp. and
power supply voltage.)
Aging
Startup Time (Note
2)
Input Logic Levels
Input Logic High
Input Logic Low
Output Disable Time
(Note
3)
Output Enable Time
Enable Pull-up Resistor
(Note
4)
CMOS Output
Output Logic Levels
Output Logic High
Output Logic Low
Note 1:
2:
3:
4:
V
OH
V
OL
0.9
V
DD
—
—
—
—
0.1
V
DD
V
I = ±6 mA
—
Typ.
—
—
20
31
—
—
—
—
—
—
—
—
—
—
40
Max.
3.6
0.095
22
35
±10
±20
—
—
—
—
0.75
V
DD
—
—
—
—
—
±25
±50
±5
5
—
0.25
V
DD
5
5
20
—
V
ns
ms
ns
k
—
—
DSC1101
DSC1121
Pull-up Resistor Exist
ppm
ms
ppm
mA
Units
V
—
DSC1101, EN pin low, output
is disabled
DSC1121, EN pin low, output
is disabled
Output enabled, C
L
= 15 pF,
F
0
= 100 MHz
Ext Comm. & Ind. only
All temp ranges
All temp ranges
All temp ranges
1 year @ 25°C
T = 25°C
Conditions
f
f
t
SU
V
IH
V
IL
t
DS
t
EN
—
Pin 6 V
DD
should be filtered with 0.1
μF
capacitor.
t
SU
is time to 100 ppm of output frequency after V
DD
is applied and outputs are enabled.
Output Waveform and Test Circuit figures define the parameters.
Output is enabled if pad is floated or not connected.
DS20005613C-page 2
2017-2019 Microchip Technology Inc.
DSC1101/21
DC CHARACTERISTICS (CONTINUED)
Electrical Characteristics
Parameters
Output Transition Time
Rise Time
Fall Time
Sym.
t
R
t
F
Min.
—
—
2.3
Frequency
f
0
3.3
Output Duty Cycle
Period Jitter
Integrated Phase Noise
Note 1:
2:
3:
4:
SYM
J
PER
J
PH
45
—
—
—
—
—
—
3
0.3
0.38
1.7
170
55
—
—
—
2
ps
RMS
%
ps
RMS
Typ.
1.1
1.3
—
Max.
2
2
170
MHz
ns
Units
Conditions
20% to 80%
C
L
= 15 pF
C
L
= 15 pF, –20°C to +70°C
and –40°C to +85°C
C
L
= 15 pF, –40°C to +105°C
and –55°C to +125°C
—
F
OUT
= 125 MHz
200 kHz to 20 MHz @ 125 MHz
100 kHz to 20 MHz @ 125 MHz
12 kHz to 20 MHz @ 125 MHz
Pin 6 V
DD
should be filtered with 0.1
μF
capacitor.
t
SU
is time to 100 ppm of output frequency after V
DD
is applied and outputs are enabled.
Output Waveform and Test Circuit figures define the parameters.
Output is enabled if pad is floated or not connected.
2017-2019 Microchip Technology Inc.
DS20005613C-page 3
DSC1101/21
TEMPERATURE SPECIFICATIONS (Note
1)
Parameters
Temperature Ranges
T
A
Operating Temperature Range (T)
T
A
T
A
T
A
Junction Operating Temperature
Storage Temperature Range
Soldering Temperature Range
Note 1:
T
J
T
A
T
S
–20
–40
–40
–55
—
–40
—
—
—
—
—
—
—
—
+70
+85
+105
+125
+150
+150
+260
°C
°C
°C
°C
°C
°C
°C
Ordering Option E
Ordering Option I
Ordering Option L
Ordering Option M
—
—
40 sec. max
Sym.
Min.
Typ.
Max.
Units
Conditions
The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable
junction temperature and the thermal resistance from junction to air (i.e., T
A
, T
J
,
JA
). Exceeding the
maximum allowable power dissipation will cause the device operating junction temperature to exceed the
maximum +125°C rating. Sustained junction temperatures above +125°C can impact the device reliability.
DS20005613C-page 4
2017-2019 Microchip Technology Inc.
DSC1101/21
2.0
Note:
NOMINAL PERFORMANCE CURVES
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
I want to ask about the non-maskable interrupt of MSP430. NMI I want to use the RESET pin as the interrupt input pin, but no matter how I try, it doesn't work. Everyone, please check if there is any p...
Is the signal output by the LLC of SAA7113 a square wave or some other waveform? I found that the signal output by my LLC is a sawtooth wave. Do you think this waveform is correct?...
A line scan lens is an industrial lens used with line scan cameras. Its imaging principle is to capture the image of the workpiece using a linear sensor and then perform digital signal processing t...[Details]
On August 25th, SK Hynix announced that it has completed development and entered mass production of its 321-layer, 2Tb QLC NAND flash memory product. This achievement marks the world's first applic...[Details]
Robotics
has become
LiDAR
's "second growth curve."
While LiDAR was still battling with its "pure vision" rivals in the automotive field, another field ignited the demand f...[Details]
On August 21st, Zhiyuan Robotics revealed at its first partner conference that it expects shipments to reach thousands of units this year and tens of thousands next year. The company hopes to reach...[Details]
The all-new MG4 was recently officially announced on the Ministry of Industry and Information Technology's (MIIT) new vehicle announcement. The all-new MG4's semi-solid-state battery version addres...[Details]
One of the most core components of electric vehicles is the motor. The power supply provides electrical energy to the motor, which converts this electrical energy into mechanical energy, which in t...[Details]
UPS stands for Uninterruptible Power Supply, which includes energy storage devices. It is mainly used to provide uninterruptible power supply for devices that require high power stability.
...[Details]
1. Multi-channel DAC technology bottleneck
Currently,
the development of multi-channel DAC technology focuses on two core challenges.
First, industrial applications urgently ...[Details]
A multilevel inverter converts a DC signal into a multilevel staircase waveform. Instead of a straight positive-negative output waveform, the output waveform of a multilevel inverter alternates in ...[Details]
On August 21st, BYD announced the launch of its next-generation "Little White Pile" product, the "Lingchong"
charging
pile
, which is now available for general sale. This charging pile feat...[Details]
China, August 21, 2025 – STMicroelectronics (NYSE: STM), a world-leading semiconductor company serving a wide range of electronics applications, has published its IFRS 2025 semi-annual financial re...[Details]
Electric vehicles will revolutionize transportation, changing fuel consumption, carbon emissions, costs, maintenance, and driving habits. Currently, a major selling point for electric vehicles is t...[Details]
introduction
With the development of society, people's requirements for the quality of refrigerated and frozen foods are constantly improving. The changes in food appearance and nutritional co...[Details]
introduction
The rapid adoption of computers has led to a growing number of tasks being performed on them. People from all walks of life, especially programmers and writers, are spending incre...[Details]
As the power density of modern electronic systems continues to increase, effective thermal management has become critical to ensuring system performance, reliability, and longevity—especially in hi...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
