EEWORLDEEWORLDEEWORLD

Part Number

Search

54122-808-69-0800RLF

Description
Board Connector, 138 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Kinked Leads Terminal, Locking, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size107KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

54122-808-69-0800RLF Overview

Board Connector, 138 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Kinked Leads Terminal, Locking, Black Insulator, Receptacle

54122-808-69-0800RLF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAmphenol
Reach Compliance Codecompli
body width0.19 inch
subject depth0.315 inch
body length6.9 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedMatte Tin (Sn) - with Nickel (Ni) barrie
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee3
Manufacturer's serial number54122
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness15u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.12 inch
Terminal pitch2.54 mm
Termination typeSOLDER KINKED LEADS
Total number of contacts138
PDM: Rev:K
STATUS:
Released
Printed: Mar 10, 2011
.
Can 0 ohm resistors be connected in series on several SPI lines?
I use SPI between my STM32 and CPLD, and each SPI port line is connected in series with a 0 ohm resistor. Now SPI communication is not working. Is it because of the series resistor?...
kelywu stm32/stm8
CC2541 Bluetooth pcb antenna gain calculation
RT, I'm a newbie, can anyone give me some guidance?...
顺手牵→猪 PCB Design
LED flasher operating at low voltage
The low voltage microprocessor supervisory circuit can form a low voltage, low power LED flasher, and can adjust the lighting time and flashing rate. The μP supervisory circuit (IC1) is powered by two...
lorant Analog electronics
How are fonts defined in the TI graphics library?
Can the fonts in the TI graphics library be matched with the fonts in the PC? cm cmsc cmss cmtt fixedThe suffix B is bold. The suffix "I" is italic....
蓝雨夜 TI Technology Forum
Can FPGA be used to design COMS camera to collect data and control motor?
I collect data through the CMOS camera, mainly the weld image, and control the motor to drive the car to move through the FPGA, with adaptive feedback. I hope you can draw me an overall functional dia...
lovetao220 FPGA/CPLD
About 485 Communications
PC communicates with MCU via 232-485. 485 chip is connected to automatic transceiver. Pull-up and pull-down resistors of A and B are connected, but why can PC only receive data from MCU, but the data ...
jmhuanghb Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1135  1055  92  803  1602  23  22  2  17  33 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号