PQ60025EGL25
35-75V
Input
Technical
Specification
Eighth-brick
DC-DC Converter
100V
Transient Input
2.5V
Output
25A
Current
2000V dc
Isolation
The PQ60025EGL25 PowerQor Giga eighth-brick
converter is a next-generation, board-mountable,
isolated, fixed switching frequency DC/DC converter
that uses synchronous rectification to achieve extremely
high conversion efficiency. The power dissipated by
the converter is so low that a heatsink is not required,
which saves cost, weight, height, and application
effort. All of the power and control components are
mounted to the multi-layer PCB substrate with high-
yield surface mount technology. Since the PowerQor
converter has no explicit thermal connections, it is
extremely reliable.
Protection Features
•
•
•
•
•
Input under-voltage lockout disables converter at low Vin conditions
Output current limit
Short circuit protection
Protection from permanent damage and hazardous conditions
Thermal shutdown protects converter from abnormal conditions
PQ60025EGL25 Model
Operational Features
•
•
•
•
•
•
High efficiency, 89% half load, 85% at full load
Delivers 25A full power with minimal derating - no heatsink required
Operating input voltage range: 35-75V
Input voltage transient capability: 100V, 100ms
Fixed frequency switching provides predictable EMI
No minimum load requirement
Mechanical Features
•
•
•
•
Industry standard eighth-brick pin-out configuration
Industry standard size: 0.90” x 2.3”
Total height less than 0.335” (8.5mm)
Total weight: 0.68 oz. (19g)
Control Features
• On/Off control referenced to input side
• Positive and negative logic options are available
• Remote sense for Vout compensates for output distribution drops
Contents
Safety Features
•
•
•
•
UL 60950-1:2007
EN60950-1/A11:2009/A1:2010
CAN/CSA-C22.2 No. 60950-1:2007
IEC 61000-4-2
Mechanical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Standards & Qualifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Technical Figures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Applications Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
www.synqor.com
Doc.# 005-2EG625B Rev. B
02/11/11
Page No.
Product # PQ60025EGL25
Phone 1-888-567-9596
Page 1
Open Frame Mechanical Diagram
PQ60025EGL25
Technical
Specification
Top View
0.600 (15.24)
0.450 (11.43)
0.300 (7.62)
0.150 (3.81)
0.90 (22.86)
EGA
0.410 (10.41)
max height
See Note 9
8 7 6 5 4
Side View
.340 ±.014
(8.64 ±0.35)
0.110
(2.79)
See Note 3
2.30
(58.42)
2.00
(50.8)
0.14
(3.56)
1
0.150
(3.81)
0.300 (7.62)
0.600 (15.24)
2
3
PIN FAR SIDE
TYPICAL
SEE NOTES
1, 2, AND 3
EGA
Bottom side
Clearance
0.089 (2.26)
min clearance
See Note 9
.019 ±.013
(0.48 ±0.33)
BOTTOMSIDE
CLEARANCE
NOTES
1)
2)
3)
4)
5)
6)
Pins 1-3, 5-7 are 0.040” (1.02mm) diameter with 0.080” (2.03mm)
diameter standoff shoulders.
Pins 4 and 8 are 0.062” (1.57 mm) diameter with 0.100” (2.54 mm)
diameter standoff shoulders.
Other pin extension lengths available. Recommended pin length is
0.03” (0.76mm) greater than the PCB thickness.
All Pins: Material - Copper Alloy- Finish - Matte Tin over Nickel plate
Undimensioned components are shown for visual reference only.
All dimensions in inches (mm)
Tolerances: x.xx +/-0.02 in. (x.x +/- 0.5mm)
x.xxx +/-0.010 in. (x.xx +/-0.25mm)
Weight: 0.68 oz. (19g) typical
Workmanship: Meets or exceeds IPC-A-610C Class II
UL/TUV standards require a clearance greater than 0.04” (1.02mm)
between input and output for Basic insulation. This issue should be
considered if any copper traces are on the top side of the user’s board.
Note that the ferrite cores are considered part of the input/primary
circuit
Pin
1
2
3
4
5
6
7
8
Notes:
Name
Vin(+)
ON/OFF
Vin(–)
Vout(–)
Sense (-)
Trim
Sense (+)
Vout(+)
PIN DESIGNATIONS
Function
Positive input voltage
TTL input to turn converter on and off,
referenced to Vin(–), with internal pull up.
Negative input voltage
Negative output voltage
Negative remote sense (see note 1)
Output voltage trim (see note 2)
Positive remote sense (see note 3)
Positive output voltage
7)
8)
9)
1) Pin 5 must be connected to Vout(-).
2)
Leave Pin 6 open for nominal output voltage.
3)
Pin 7 must be connected to Vout(+).
Product # PQ60025EGL25
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2EG625B Rev. B
02/11/11
Page 2
Technical Specification
PQ60025EGL25 Electrical Characteristics
Input:
Output:
Current:
Package:
35-75V
2.5V
25A
Eighth-brick
Ta = 25 °C, airflow rate = 300 LFM, Vin = 48V dc unless otherwise noted; full operating temperature range is -40 °C to +100 °C baseplate temperature
with appropriate power derating. Specifications subject to change without notice.
Parameter
ABSOLUTE MAXIMUM RATINGS
Input Voltage
Non-Operating
Operating
Operating Transient Protection
Isolation Voltage (Input to Output)
Operating Temperature
Storage Temperature
Voltage at ON/OFF input pin
INPUT CHARACTERISTICS
Operating Input Voltage Range
Input Under-Voltage Lockout
Turn-On Voltage Threshold
Turn-Off Voltage Threshold
Lockout Voltage Hysteresis
Maximum Input Current
No-Load Input Current
Disabled Input Current
Inrush Current Transient Rating
Response to Input Transient
Input Reflected Ripple Current
Input Terminal Ripple Current
Recommended Input Fuse
Recommended External Input Capacitance
Input Filter Component Values (L\C)
OUTPUT CHARACTERISTICS
Output Voltage Set Point
Output Voltage Regulation
Over Line
Over Load
Over Temperature
Total Output Voltage Range
Output Voltage Ripple and Noise
Peak-to-Peak
RMS
Operating Output Current Range
Output DC Current-Limit Inception
Output DC Current-Limit Shutdown Voltage
Back-Drive Current Limit while Enabled
Back-Drive Current Limit while Disabled
Maximum Output Capacitance Electrolytic
EFFICIENCY
100% Load
50% Load
Min.
Typ.
Max.
100
80
100
2000
100
125
18
Units Notes & Conditions
V
V
V
V
°C
°C
V
V
V
V
V
A
mA
mA
A²s
mV
mA
mA
A
µF
µH\µF
V
%\mV
%\mV
Mv
V
mV
mV
A
A
V
A
mA
µF
%
%
Continuous
Continuous
100ms transient
Basic level, Pollution Degree 2
-40
-55
-2
35
31.5
29.5
2.4
48
33.3
31.5
2.8
32
2
150
4.2
220
52
34.4
32.4
3.2
2.4
4
0.01
100% Load, 35V Vin
20
33
47
2.2\3.3
2.50
±0.1 \ 2.5
±0.1 \ 2.5
±13
2.43
70
17
0
26.0
27.5
1.2
0.55
10
2.525
±0.2 \ 5
±0.2 \ 5
±38
2.57
130
30
25
30.0
1000V/ms input transient
RMS thru10μH inductor
RMS
Fast acting external fuse recommended
Typical ESR 0.1-0.2Ω; Figure 13
Internal values
2.475
50
16,000
Over sample, line, load, temperature & life
20MHz bandwidth
Full load
Full load
Subject to thermal derating
Output Voltage 10% Low
See note 3
Negative current drawn from output
Negative current drawn from output
2.5Vout at 25A Resistive Load
Figures 1 - 2
Figures 1 - 2
85
89
Product # PQ60025EGL25
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2EG625B Rev. B
02/11/11
Page 3
Technical Specification
Input:
Output:
Current:
Package:
35-75V
2.5V
25A
Eighth-brick
PQ60025EGL25 Electrical Characteristics (continued)
Ta = 25 °C, airflow rate = 300 LFM, Vin = 48V dc unless otherwise noted; full operating temperature range is -40 °C to +100 °C baseplate temperature
with appropriate power derating. Specifications subject to change without notice.
Parameter
Min.
Typ.
65
120
180
200
29
220
Max.
Units Notes & Conditions
dB
mV
mV
µs
ms
ms
%
V
MΩ
pF
120 Hz
50% to 75% to 50% Iout max
50% to 75% to 50% Iout max
To within 1% Vout nom
Full load, Vout=90% nom; Figures 9 & 10
-40°C to +125°C
16,000 μF load capacitance, Iout = 0A
See Absolute Maximum Ratings
See Note 4
Package rated to 150°C
UL rated max operating temp 130°C
DYNAMIC CHARACTERISTICS
Input Voltage Ripple Rejection
Output Voltage during Load Current Transient
Step Change in Output Current (0.1A/µs)
Step Change in Output Current (5A/µs)
Settling time
Turn-On Transient
Turn-On Time
Start-Up Inhibit Time
200
Output Voltage Overshoot
ISOLATION CHARACTERISTICS
Isolation Voltage (dielectric strength)
Isolation Resistance
Isolation Capacitance (input to output)
TEMPERATURE LIMITS FOR POWER DERATING CURVES
Semiconductor Junction Temperature
Board Temperature
Transformer Temperature
FEATURE CHARACTERISTICS
Switching Frequency
245
ON/OFF Control (Option P)
Off-State Voltage
-2.0
On-State Voltage
2.4
ON/OFF Control (Option N)
Off-State Voltage
2.4
On-State Voltage
-2.0
ON/OFF Control (Either Option)
Pull-Up Voltage
Pull-Up Resistance
Output Voltage Trim Range
-20
Output Voltage Remote Sense Range
Output Over-Voltage Protection
120
Over-Temperature Shutdown
Over-Temperature Shutdown Restart Hysteresis
RELIABILITY CHARACTERISTICS
Calculated MTBF (Telcordia)
Calculated MTBF (MIL-217)
Field Demonstrated MTBF
240
0
2000
30
470
125
125
125
260
285
0.8
18.0
18
0.8
Vin/6
40
15.00
+10
+10
123
°C
°C
°C
kHz
V
V
Application notes; Figures A & B
V
kΩ
%
%
°C
°C
Measured across Pins 8 & 4; Figure C
Over Full Temperature Range; % of nominial Vout
Average PCB Temperature
125
125
10
2.5
1.1
10
6
Hrs. TR-NWT-000332; 80% load, 300LFM, 40°C Ta
10
6
Hrs. MIL-HDBK-217F; 80% load, 300LFM, 40°C Ta
10
6
Hrs. See our website for details
Product # PQ60025EGL25
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2EG625B Rev. B
02/11/11
Page 4
Technical Specification
Standards Compliance & Qualification Testing
Parameter
Notes & Conditions
Input:
Output:
Current:
Package:
35-75V
2.5V
25A
Eighth-brick
STANDARDS COMPLIANCE
UL 60950-1:2007
Basic insulation
EN60950-1/A11:2009/A1:2010
CAN/CSA-C22.2 No. 60950-1:2007
IEC 61000-4-2
ESD test, 8 kV - NP, 15 kV air - NP (Normal Performance)
Note: An external input fuse must always be used to meet these safety requirements. Contact SynQor for official safety certificates on new
releases or download from the SynQor website.
Parameter
QUALIFICATION TESTING
Life Test
Vibration
Mechanical Shock
Temperature Cycling
Power/Thermal Cycling
Design Marginality
Humidity
Solderability
# Units
32
5
5
10
5
5
5
15 pins
Test Conditions
95% rated Vin and load, units at derating point, 1000 hours
10-55 Hz sweep, 0.060" total excursion, 1 min./sweep, 120 sweeps for 3 axis
100g minimum, 2 drops in x, y and z axis
-40 °C to 100 °C, unit temp. ramp 15 °C/min., 500 cycles
Toperating = min to max, Vin = min to max, full load, 100 cycles
Tmin-10 °C to Tmax+10 °C, 5 °C steps, Vin = min to max, 0-105% load
85 °C, 85% RH, 1000 hours, continuous Vin applied except 5 min/day
MIL-STD-883, method 2003
Product # PQ60025EGL25
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2EG625B Rev. B
02/11/11
Page 5
stm32/stm8
京公网安备 11010802033920号
EEWORLD
