EEWORLDEEWORLDEEWORLD

Part Number

Search

PPC1/2253520BLF13

Description
RESISTOR, METAL GLAZE/THICK FILM, 0.5W, 0.1%, 25ppm, 352ohm, SURFACE MOUNT, 2008, MELF, ROHS COMPLIANT
CategoryPassive components    The resistor   
File Size178KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance  
Download Datasheet Parametric View All

PPC1/2253520BLF13 Overview

RESISTOR, METAL GLAZE/THICK FILM, 0.5W, 0.1%, 25ppm, 352ohm, SURFACE MOUNT, 2008, MELF, ROHS COMPLIANT

PPC1/2253520BLF13 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerTT Electronics plc
package instructionMELF, ROHS COMPLIANT
Reach Compliance Codecompli
ECCN codeEAR99
Other featuresPRECISION
Manufacturer's serial numberPPC
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Package shapeCYLINDRICAL PACKAGE
method of packingTR, 13 INCH
Rated power dissipation(P)0.5 W
Rated temperature70 °C
resistance352 Ω
Resistor typeFIXED RESISTOR
size code2008
surface mountYES
technologyMETAL GLAZE/THICK FILM
Temperature Coefficient25 ppm/°C
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage300 V
Metal Glaze
Surface Mount
Precision Power Chip
PPC Series
Surge tolerant
Up to 1000 volts
Tight TCR - 25 ppm/°C
Tolerance down to ±0.1%
Solder over nickel
barrier
High
temperature
dielectric
coating
Metal Glaze™ thick
film element fired
at 1000°C to solid
ceramic substrate
Electrical Data
Size
Code
B
D
F
H
Industry
Footprint
1206
2010
2512
3610
IRC
Type
PPC1/8
PPC1/2
PPC1
PPC2
Power
Rating at
70°C (W)
1/8 W
1/2 W
1W
2W 1.33W
Working
Voltage
200
300
350
500
Resistance
Range
(ohms)
100 - 10K
100 - 10K
100 - 10K
100 - 10K
0.1% (B)
0.25% (C)
0.5% (D)
Tolerance
(±%)
Qty /
Reel (7")
2500
1500
N/A
N/A
Qty /
Reel (13")
10000
5000
5000
1500
Environmental Data
Characteristics
Temperature Coefficient
Thermal Shock
Low Temperature Operation
Short Time Overload
High Temperature Exposure
Resistance to Bonding
Exposure
Solderability
Moisture Resistance
Life Test
Terminal Adhesion Strength
Maximum Change
As specified
±0.5% + 0.01 ohm
±0.25% + 0.01 ohm
±0.5% + 0.01 ohm
±0.5% + 0.01 ohm
±0.25% + 0.01 ohm
95% minimum coverage
±0.5% + 0.01 ohm
±0.5% + 0.01 ohm
±1% + 0.01 ohm
±1% + 0.01 ohm
no mechanical damage
Test Method
MIL-R-55342E Par 4.7.9 (-55°C + 125°C)
MIL-R-55342E Par 4.7.3 (-65°C + 150°C, 5 cycles)
MIL-R-55342E Par 4.7.4 (-65°C @ working voltage)
MIL-R-55342E Par 4.7.5 2.5 x
for 5 seconds
MIL-R-55342E Par 4.7.6 (+150°C for 100 hours)
MIL-R-55342E Par 4.7.7 (Reflow soldered to board at 260°C
for 10 seconds)
MIL-STD-202, Method 208 (245°C for 5 seconds)
MIL-R-55342E Par 4.7.8 (10 cycles, total 240 hours)
MIL-R-55342E Par 4.7.10 (2000 hours at 70°C intermittent)
1200 gram push from underside of mounted chip for 60
seconds
Chip mounted in center of 90mm long board, deflected 1mm
so as to exert pull on chip contacts for 5 seconds
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
Wire and Film Technologies Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
PPC Series Issue November 2008 Sheet 1 of 3
The initial functions of the EZ430-Chronos wireless fishing sports watch I modified have been realized as planned.
Originally, the data transmission function test with the computer had been successful many days ago, but the specific interface was not completed. However, two or three days ago, due to a detail probl...
wangfuchong Microcontroller MCU
Lattice management distribution problem
I use lattice's ECP3 95E, which is a FBGA672 package. The design has a ddr2 sdram controller. The lattice datasheet says that for signals such as DQS , dedicated pins must be used, and they are usuall...
eeleader FPGA/CPLD
Does anyone have the antenna test program for 2530?
The board has been made for a long time, but I can't find the open line test program for 2530 under IAR760. There is no such program in the 07 protocol stack. If anyone can give me a copy, I will be v...
panxm916 RF/Wirelessly
Pulse fast charging design for lead-acid batteries in electric vehicles
Abstract: The principle of fast charging is explained. In view of various problems that occur during battery charging, a pulse fast charging scheme with graded constant current is adopted, and the des...
hero Power technology
Concept and solution of ultra-fast battery charging
The battery of an electric vehicle can be used for about two hours, which is very inconvenient for users. It is normal to run out of power when going out. If we have a fast charger, we can quickly rep...
zbz0529 Power technology
Blackfin series ADSP512 has no flash, how to burn the program? I hope the experts can give me some advice
[size=5]Blackfin series ADSP512 has no flash, how to burn the program? I hope the experts can give me some advice[/size]...
hopewell99 ADI Reference Circuit

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1109  928  1250  1870  2742  23  19  26  38  56 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号