EEWORLDEEWORLDEEWORLD

Part Number

Search

PPC1251960DLF13

Description
RESISTOR, METAL GLAZE/THICK FILM, 1W, 0.5%, 25ppm, 196ohm, SURFACE MOUNT, 2508, MELF, ROHS COMPLIANT
CategoryPassive components    The resistor   
File Size178KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance  
Download Datasheet Parametric View All

PPC1251960DLF13 Overview

RESISTOR, METAL GLAZE/THICK FILM, 1W, 0.5%, 25ppm, 196ohm, SURFACE MOUNT, 2508, MELF, ROHS COMPLIANT

PPC1251960DLF13 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerTT Electronics plc
package instructionMELF, ROHS COMPLIANT
Reach Compliance Codecompli
ECCN codeEAR99
Other featuresPRECISION
Manufacturer's serial numberPPC
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Package shapeCYLINDRICAL PACKAGE
method of packingTR, 13 INCH
Rated power dissipation(P)1 W
Rated temperature70 °C
resistance196 Ω
Resistor typeFIXED RESISTOR
size code2508
surface mountYES
technologyMETAL GLAZE/THICK FILM
Temperature Coefficient25 ppm/°C
Terminal shapeWRAPAROUND
Tolerance0.5%
Operating Voltage350 V
Metal Glaze
Surface Mount
Precision Power Chip
PPC Series
Surge tolerant
Up to 1000 volts
Tight TCR - 25 ppm/°C
Tolerance down to ±0.1%
Solder over nickel
barrier
High
temperature
dielectric
coating
Metal Glaze™ thick
film element fired
at 1000°C to solid
ceramic substrate
Electrical Data
Size
Code
B
D
F
H
Industry
Footprint
1206
2010
2512
3610
IRC
Type
PPC1/8
PPC1/2
PPC1
PPC2
Power
Rating at
70°C (W)
1/8 W
1/2 W
1W
2W 1.33W
Working
Voltage
200
300
350
500
Resistance
Range
(ohms)
100 - 10K
100 - 10K
100 - 10K
100 - 10K
0.1% (B)
0.25% (C)
0.5% (D)
Tolerance
(±%)
Qty /
Reel (7")
2500
1500
N/A
N/A
Qty /
Reel (13")
10000
5000
5000
1500
Environmental Data
Characteristics
Temperature Coefficient
Thermal Shock
Low Temperature Operation
Short Time Overload
High Temperature Exposure
Resistance to Bonding
Exposure
Solderability
Moisture Resistance
Life Test
Terminal Adhesion Strength
Maximum Change
As specified
±0.5% + 0.01 ohm
±0.25% + 0.01 ohm
±0.5% + 0.01 ohm
±0.5% + 0.01 ohm
±0.25% + 0.01 ohm
95% minimum coverage
±0.5% + 0.01 ohm
±0.5% + 0.01 ohm
±1% + 0.01 ohm
±1% + 0.01 ohm
no mechanical damage
Test Method
MIL-R-55342E Par 4.7.9 (-55°C + 125°C)
MIL-R-55342E Par 4.7.3 (-65°C + 150°C, 5 cycles)
MIL-R-55342E Par 4.7.4 (-65°C @ working voltage)
MIL-R-55342E Par 4.7.5 2.5 x
for 5 seconds
MIL-R-55342E Par 4.7.6 (+150°C for 100 hours)
MIL-R-55342E Par 4.7.7 (Reflow soldered to board at 260°C
for 10 seconds)
MIL-STD-202, Method 208 (245°C for 5 seconds)
MIL-R-55342E Par 4.7.8 (10 cycles, total 240 hours)
MIL-R-55342E Par 4.7.10 (2000 hours at 70°C intermittent)
1200 gram push from underside of mounted chip for 60
seconds
Chip mounted in center of 90mm long board, deflected 1mm
so as to exert pull on chip contacts for 5 seconds
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
Wire and Film Technologies Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
PPC Series Issue November 2008 Sheet 1 of 3
Do you want to participate in such a post?
Based on the post "Retain the beautiful scenery around you", I have an idea to post a theme post for each season of the year. You can share some photos or interesting things, or you can share a delici...
mmmllb Talking
Why does BTS723 have 9V output?
VCC=DC24V, when s3 or s4 is pressed, it can output 24V, when S3 or S4 is not pressed, why does BTS723 have 9V output? According to the PDF, it should output 0 [[i] This post was last edited by simonpr...
simonprince Analog electronics
IO port photoelectric isolation problem
I would like to ask about the I/O input and output. In the process of system design, all input and output digital quantities are photoelectrically isolated. Photoelectric isolation can effectively sup...
wolfjj DSP and ARM Processors
Wide VIN DC/DC Power Solution
...
杨柳青年 Analogue and Mixed Signal
Several issues about embedded CNC
Recently, my supervisor asked me to do a project on embedded CNC. I originally studied mechanics and know very little about this area. I have a few questions to ask you masters: How to design the keyb...
lhb111403 Embedded System
STM32 beginners ask about the problem of FSMC hanging monochrome screen
I am a beginner of STM32F. I want to use the FSMC interface of STM32F103VC to connect a monochrome screen. The timing is shown in the figure. I would like to ask you how to connect the hardware. I hea...
mikerain stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2732  85  2470  754  1440  56  2  50  16  29 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号