EEWORLDEEWORLDEEWORLD

Part Number

Search

284T45F503B24AT

Description
Precision Potentiometer
File Size319KB,2 Pages
ManufacturerCTS [CTS Corporation]
Download Datasheet View All

284T45F503B24AT Overview

Precision Potentiometer

Series 284
Data Sheet
Electrocomponents
Industrial
16mm Size Slim
Conductive Plastic
Precision Rotary Sensor
Features
Up to 3 Million Life Cycles
®
Precision Potentiometer
Electrical and Mechanical Specifications
Resistance Range
1 K through 500 K ohms, linear
Resistance Tolerance
± 10%, ± 20%
Power Rating
0.25 watts @ 55°C
Dielectric Strength
500 VDC for 1 minute
Maximum Operating Voltage
350 VDC
Insulation Resistance
100 Megohms minimum @ 100 VDC
Rotation Angle
Total Rotational Angle : 250°
Effective Electrical Angle : 60°, 220°
Rotational Torque
IP40 : 3~30 gf-cm
IP54 & IP67 : 20~120 gf-cm
Stop Strength
9 kgf-cm minimum
Push-Pull Strength of Shaft
13.6 kg for 10 seconds
Mounting Information
Bushing Mount
Rotational life
3M Cycles
(60° Effective Electrical Angle)
2M Cycles
(220° Effective Electrical Angle)
Linearity
± 2%
Temperature
Operating : -40°C
- 125°C
Storage : -55°C
- 150°C
Solder Heat Resistance
350°C
for 5 seconds
Ingress Protection Rating
IP40, IP54, IP67
Vibration
15G, 10 to 2000 Hz
1-2
CTS Electrocomponents
© 2012 CTS Corporation. All rights reserved. Information subject to change.
02/16/12
www.ctscorp.com
What should I do if an error message appears when two components in AD are too close to each other?
In AD, an error message appears when two components are too close to each other. Where can I adjust this value (the minimum allowable distance)?...
cwzqhdx PCB Design
Analyze PCB design routing rate and design efficiency skills
Source: pcb.comhttp://www.hampoo.comIntroduction: In PCB wiring design, there is a complete set of methods to improve the routing rate. Here, we provide you with effective techniques to improve the ro...
wswnihao PCB Design
Serial port response signal
I want to design a communication protocol. After my machine 1 sends a handshake signal, it cannot receive the response signal from machine 2. However, when I connect machine 2 to the PC's serial debug...
louislen Embedded System
Technology Marketing, You Can Too!
If you are tired of the dull life of an engineer, or hope to seek new career opportunities, if you are confident in your ability to express yourself in writing, understand mainstream electronic techno...
猫熊 Recruitment
The problem of microcontroller reset caused by the moment the motor is powered on
The driving signal has been isolated by an optocoupler, the reset circuit is a low-level reset, VCC is connected to a resistor, and the capacitor is grounded. What is the reason?...
csallon Embedded System
TMS320C6455 GPIO interruption problem
I am new to DSP and I have a problem. Please help me! ! When configuring GPIO5 as a hardware interrupt, I use the code in CSL to configure it. The pin selected is CSL_GPIO_PIN5. In the datasheet, the ...
Joying DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2860  1666  2809  908  772  58  34  57  19  16 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号