313LCPTAALDGE datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > 313LCPTAALDGE

Preview

313LCPTAALDGE: DescriptionSUBMERSIBLE LEVEL TRANSMITTER; File Size90KB，2 Pages; ManufacturerETC2

Download Datasheet View All

313LCPTAALDGE Overview

SUBMERSIBLE LEVEL TRANSMITTER

Preview

Download Datasheet

View All

SUBMERSIBLE LEVEL TRANSMITTER

Model 313L

GENERAL PURPOSE

FEATURES:

•

All-welded, stainless steel construction

Rugged, all encapsulated electronics.

Leakproof

1/2” NPT conduit thread standard

Standard

PRESSURE RANGES:

• From 0-3 through 0-100 psig

(See ordering guide.)

ACCURACY:

• From

±0.1%

FSO (RSS) to

±0.5%

FSO (RSS)

(See specifications & ordering guide.)

with Option LJ

tapered inlet with

stand off plate

ORDERING GUIDE

Ordering: Specify model, and pressure range and indicate modifications or

accessories required.

Use the following codes to identify desired item. Example 313L-B-PZ-LJ

MODEL

SERIES

RANGE

OPTIONS

•

MODEL

313L 4-20mA

SERIES

±0.5%

FSO (RSS)

±0.2%

FSO (RSS)

±0.1%

FSO (RSS)

•

•/•/•

OPTIONS

None (standard connector)

Alternate cable length (specify)

ALTERNATE PRESSURE PORT

1/8” NPT (F)

1/8” NPT (M)

Tapered inlet

Tapered inlet with standoff plate

PRESSURE RANGE

psi

in wc

100

150

7.5

200

300

100

GENERAL

Tefzel jacketed cable

Standardized output to

±0.5%

FSO

Alternate output, pressure units, or full scale

outputs that are non-standard

Improved temperature compensation to

±0.5%

FSO

unless otherwise specified

Alternate calibration signal

Internal calibration resistor set to 100

±0.5%

FSO

unless other wise specified

Remote cable mounted (in-line) zero & span controls. 3’ cable on open

side. Length of cable on closed side as required. (500’ maximum)

Customer special

Specifications printed on reverse side of this brochure.

GP:50 reserves the right to make product improvements and amendments to the product specification stated throughout this

brochure without prior notification. Please contact the factory on all critical dimensions and specifications for verification.

TOPE Co., Ltd.

Tel. (02) 8228-0658 • Fax. (02) 8228-0659 • E-mail: tope@ms1.hinet.net • Website: www.sensor.com.tw

SL5B-313L.02C

Recommended Resources

Soft start regulated power supply circuit 2

Load open circuit indication circuit

Semiconductor self-excited excitation circuit

Maintenance-free battery power supply diagram

Circuit diagram of automatically removing bias voltage with one touch of A and D converter

875p computer motherboard circuit diagram_100

Electronics Industry: Five Minefields You Must Know: [align=left][b][font=宋体]Minefield[/font]1[/b][b][font=宋体], second-hand goods[/font][/b][/align][align=left] [font=宋体]Buy the electronic components that are left over from use or sales and are piled up...; 称心如意 Discrete Device

Newbie question: How to install C51 and MDK at the same time: I have installed MDK3.22a, but I cannot compile C51 programs. What else should I install?...; zhangsf Embedded System

Can Altium implement the function of the network label indicator page?: [size=6][backcolor=yellow]As shown in the figure above, there is a 5 after LED1, which means it is connected to page 5[/size][/backcolor][backcolor=yellow][size=6][backcolor=rgb(255, 255, 0)][size=6]A...; flying510 PCB Design

A word of caution when grounding ADC outputs: [i=s]This post was last edited by qwqwqw2088 on 2016-5-19 10:12[/i] Although many converters have tri-state outputs/inputs, these registers are still on-chip; they allow data pin signals to couple int...; qwqwqw2088 Analogue and Mixed Signal

I would like to ask how a win32 project can call an interface when the interface is initialized.: I am learning mobile phone development and now I have set up a win32 project. By default, there is a white screen when I run the program on the simulator. Now I want to call a dialog box with the ID d...; ATT001 Embedded System

Will the WRITE_PORT_UCHAR() function cause a blue screen reboot?: When I add the blue code below to the driver, the system will reboot with a blue screen. What is the reason? Is it that the WRITE_PORT_UCHAR function cannot be called directly? NTSTATUS WinIoDispatch(...; tonyleu111 Embedded System

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components