EEWORLDEEWORLDEEWORLD

Part Number

Search

3GV14D-80T-156.25

Description
14 pin Dual-in-Line
CategoryPassive components    oscillator   
File Size218KB,1 Pages
ManufacturerEuroquartz
Websitehttp://www.euroquartz.co.uk/
Environmental Compliance
Download Datasheet Parametric View All

3GV14D-80T-156.25 Overview

14 pin Dual-in-Line

3GV14D-80T-156.25 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerEuroquartz
package instructionROHS COMPLIANT PACKAGE-14/4
Reach Compliance Codecompli
Maximum control voltage2.31 V
Minimum control voltage0.99 V
Frequency Adjustment - MechanicalNO
Frequency offset/pull rate80 ppm
frequency stability25%
linearity10%
Installation featuresTHROUGH HOLE MOUNT
Nominal operating frequency156.5 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Oscillator typeLVCMOS
Output load15 pF
physical size20.2mm x 12.8mm x 5.08mm
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Nominal supply voltage3.3 V
surface mountNO
maximum symmetry55/45 %
EURO
QUARTZ
Frequency range 50.01MHz to 200MHz
LVCMOS Output
Supply Voltage 3.3 VDC
High Q fundamental mode crystal
Low jitter multiplier circuit
Low unit cost
GV14 CMOS VCXO
14 pin Dual-in-Line
OUTLINE & DIMENSIONS
DESCRIPTION
GV14 VCXOs, are packaged in an industry-standard, 14 pin Dual in
Line package. The VCXO incorporates a high Q fundamental mode
crystal and a low jitter multiplier circuit.
SPECIFICATION
Frequency Range:
Supply Voltage:
Output Logic:
Integrated Phase Jitter:
Period Jitter RMS:
Period Jitter Peak to peak:
Phase Noise:
Initial Frequency Accuracy:
Output Voltage HIGH (1):
Output Voltage LOW (0):
Pulling Range:
Temperature Stability:
Output Load:
Start-up Time:
Duty Cycle:
Rise/Fall Times:
Current Consumption:
Linearity:
Modulation Bandwidth:
Input Impedance:
Slope Polarity:
(Transfer function)
Storage Temperature:
Ageing:
Enable/Disable (Tristate):
RoHS Status:
50.01MHz to 200.0MHz
3.3 VDC ±5%
LVCMOS
2.3ps typical, 4.0ps maximum
(for 155.250MHz)
4.0ps typical (for 155.250MHz)
27.0ps typical (for 155.250MHz)
See table below
Tune to the nominal frequency
with Vc= 1.65 ±0.2VDC
90% Vdd minimum
10% Vdd maximum
From ±30ppm to ±150ppm
See table
15pF
10ms maximum, 5ms typical
50% ±5% measured at 50% Vdd
1.2ns typical (15pF load)
25mA maximum (15pF load)
10% maximum, 6% typical
25kHz minimum
2 MW minimum
Monotonic and Positive. (An
increase of control voltage
always increases output
frequency.)
-50° to +100°C
±5ppm per year maximum
Not available (4
pad package)
Fully compliant
PHASE NOISE
Offset
10Hz
100Hz
1kHz
10kHz
100kHz
1MHz
10MHz
Frequency 155.25MHz
-65dBc/Hz
-95dBc/Hz
-120dBc/Hz
-128dBc/Hz
-122dBc/Hz
-120dBc/Hz
-140dBc/Hz
FREQUENCY STABILITY
Stability Code Stability ±ppm Temp. Range
A
25
0°~+70°C
B
50
0°~+70°C
C
100
0°~+70°C
D
25
-40°~+85°C
E
50
-40°~+85°C
F
100
-40°~+85°C
If non-standard frequency stability is required
Use ‘I’ followed by stability, i.e. I20 for ±20ppm
PART NUMBERING
Example:
Supply Voltage
3 = +3.3V
Series Designator
GV14
Stability over temperature range
(See table)
Pullability in ±ppm
Pullability determinator
N = minimum
M = maximum
T = Typical
Frequency in MHz
3GV14B-80N-156.25
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 Email: info@euroquartz.co.uk www.euroquartz.co.uk
Make a server on the PC side and a client under the WinCE system. What technology should be used to implement both ends?
Make a server on the PC and a client under WinCE system. What technology should be used to implement each end? The functions supported by the client are: 1. Search server files 2. User registration 3....
cflymtk Embedded System
Filter circuit after rectification
Filter circuit after rectification...
安_然 Analog electronics
9s12g128 sci program help
I'm working on a 9s12g128 microcontroller recently. I'm using the TWR-S12G128 development board. The sci program is always working, but the sci pin does not send out data frames. Can an expert take a ...
haotianwei1983 NXP MCU
Questions about encodedecode, decode, and encode demo
Today, my boss gave me two tasks, one of which is to run the commands encodedecode, decode, and encode demo on the development board. I use a davinci board, and I don't understand what encodedecode, d...
huahuikai Embedded System
Acknowledgements | EEWorld’s 15th anniversary, thank you!
Time flies, EEWorld is 15 years old, and there are so many people to thank along the way! Here, I would like to post a special message to thank you for your company along the way!grateful: @maychang@c...
okhxyyo Talking
How to use mc1000 to enter the carriage return after scanning
I am using mc1000 and system ce50. How can I add a carriage return after the data I scanned, because I need to trigger an action when I press the carriage return. Thanks.I saw others say: How to write...
kevintu Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2289  2574  2624  1346  744  47  52  53  28  15 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号