EEWORLDEEWORLDEEWORLD

Part Number

Search

209613-7

Description
RF/MICROWAVE FIXED ATTENUATOR
CategoryWireless rf/communication    Radio frequency and microwave   
File Size34KB,1 Pages
ManufacturerTE Connectivity
Websitehttp://www.te.com
Download Datasheet Parametric View All

209613-7 Overview

RF/MICROWAVE FIXED ATTENUATOR

209613-7 Parametric

Parameter NameAttribute value
Objectid2084956849
Reach Compliance Codeunknown
Nominal attenuation7 dB
structureCOAXIAL
Maximum operating temperature75 °C
Minimum operating temperature-40 °C
RF/Microwave Device TypesFIXED ATTENUATOR
For problems that cannot be solved in this forum, will you go to the technical community on TI's official website to ask questions?
[i=s]This post was last edited by helloxieyu on 2014-9-16 17:18[/i] If you have questions that cannot be solved in this forum, will you go to the technical community on TI's official website to ask qu...
helloxieyu Microcontroller MCU
Sneak peek at new features in Altium Designer 18
[list] [*][color=rgb(34, 34, 34)][url=]Sneak peek at new features in Altium Designer 18[/url][/color] [/list]...
x1995418 PCB Design
How to analyze this circuit diagram
In this circuit, DO GND is the input signal, V0 GND is the output signal, what are the functions of the resistors in the circuit? The chip is LM358, what are the functions of R1 R2 R3 R4 R5 respective...
ytww88 Analog electronics
What does 50ohm RF routing mean in PCB? Do all high-frequency related lines need to maintain 50ohm?
Does it have to maintain 50ohm when coming out of the RF IC interface? I calculated that the line width should be 30mil using a double-layer board, but it is impossible for the IC pins to connect to a...
vinicolor PCB Design
Shielding Methods in High-Speed PCB Design
[size=3]高速PCB设计布线系统的传输速率在稳步加快的同时也带来了某种防干扰的脆弱性,这是因为传输信息的频率越高,信号的敏感性增加,同时它们的能量越来越弱,此时的布线系统就越容易受干扰。干扰无处不在,电缆及设备会对其他元件产生干扰或被其他干扰源严重干扰,例如: 计算机屏幕、移动电话、电动机、无线电转播设备、数据传输及动力电缆等。此外,潜在的窃听者、网络犯罪及黑客不断增加,因为他们对UTP电缆...
ohahaha PCB Design
How to load bitmap from SD card in EVC? LoadImage is useless because there is no LR_LOADFROMFILE
Basically as the title says. If you want to load a bitmap file from a peripheral such as an SD card, what method should you use? I tried, ::LoadBitmap and ::LoadImage() both failed. The latter can suc...
xiaolu192 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 194  2343  1513  1093  1769  4  48  31  22  36 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号