TRU050-TALGA-30M7200000 datasheet, PDF

TRU050

Complete VCXO based Phase-Locked Loop

Features

•

Output Frequencies to 65.536 MHz

•

5.0 V or 3.3Vdc Operation

•

Tri-State Output

•

Holdover on Loss of Signal Alarm

•

VCXO with CMOS Outputs

•

0/70° or –40/85° Temperature Range

C

•

Ceramic SMD Package

•

RoHS/Lead Free Compliant Versions

The TRU050, VCXO based PLL

Description

The VI TRU050 is a user-configurable crystal-based

PLL integrated circuit. It includes a digital phase

detector, op-amp, VCXO and additional integrated

functions for use in digital synchronization

applications. Loop filter software is available as well

SPICE models for circuit simulation.

Applications

•

Frequency Translation

•

Clock Smoothing

•

NRZ Clock Recovery

•

DSLAM, ADM, ATM, Aggregation, Optical

Switching/Routing, Base Station

•

Low Jitter PLL’s

Figure 1. TRU050 Block Diagram

Vectron International, 267 Lowell Rd, Unit 102, Hudson NH 03051-4916

Page 1 of 14

Tel: 1-88-VECTRON-1

•

Web:

www.vectron.com

Rev:

4/12/2016

TRU050, VCXO Based PLL

Performance Characteristics

Table 1. Electrical Performance

Parameter

Output Frequency (ordering

option)

Out 1, 5V option

Out 1, 3.3V option

1

Supply Voltage

+5

+3.3

Supply Current

Output Logic Levels

2

Output Logic High

2

Output Logic Low

Output Transition Times

2

Rise Time

2

Fall Time

Input Logic Levels

2

Output Logic High

2

Output Logic Low

Loss of Signal Indication

2

Output Logic High

2

Output Logic Low

Nominal Frequency on Loss of Signal

Output 1

Output 2

3

Symmetry or Duty Cycle

Out 1

Out 2

RCLK

Absolute Pull Range,

ordering option

o

ver operating temp, aging, power supply

variations

Symbol

Min

1.000

Typical

Maximum

Units

65.636

51.840

5.0

3.3

5.5

3.6

65

MHz

V

mA

V

ns

V

ppm

V

DD

4.5

3.0

I

DD

V

OH

V

OL

t

R

t

F

V

IH

V

IL

V

OH

V

OL

2.5

0.5

5

2.0

0.5

2.5

0.5

±75

SYM1

SYM2

RCLK

APR

40/60

45/55

40/60

±50

±80

±100

0.5

0.3

Positive

0.53

0.35

0/70 or –40/85

%

ppm

Test Conditions for APR (+5V option)

Test Conditions for APR (+3.3V option)

Gain Transfer

Phase Detector Gain

+5V option

+3.3V Option

Operating temperature,

ordering option

Control Voltage Leakage Current

V

C

V

C

4.5

3.0

V

I

VCXO

±1

rad/V

°C

uA

1. A good quality 0.01uF in parrallel with a 0.1 uf capacitor should be located as close to pin 16 to ground as possible.

2. Figure 1 defines these parameters. Figure 2 illustrates the equivalent five-gate TTL load and operating conditions under which these parameters are

tested and specified. Loads greater than 15 pF will adversely effect rise/fall time and duty cycle.

3. Symmetry is defined as (ON TIME/PERIOD with Vs=-1.4 V for both 5V and 3.3V operation.

T

R

80

%

T

F

I

DD

16

650Ω

1.4V

20

%

V

DD

+

-

.

1µF

.01µF

I

C

V

C

1

+

-

3

On Time

Period

15pF

1.8k

Figure 2. Output Waveform

Figure 3. OUT1, OUT2, RDATA and RCLK

Test Conditions (25±5°

C)

Vectron International, 267 Lowell Rd, Unit 102, Hudson NH 03051-4916

Page 2 of 14

Tel: 1-88-VECTRON-1

•

Web:

www.vectron.com

Rev:

4/12/2016

TRU050, VCXO Based PLL

Absolute Maximum Ratings

Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional

operation is not implied at these or any other conditions in excess of conditions represented in the operational

sections of this data sheet. Exposure to absolute maximum ratings for extended periods may adversely affect

device reliability.

Table 2. Absolute Maximum Ratings

Parameter

Power Supply

Storage Temperature

Soldering Temperature/Duration

Clock and Data Input Range

Symbol

V

DD

Tstorage

T

PEAK

/ t

P

CLKIN, DATAIN

Ratings

7

-55/125

260 / 40

Gnd-0.5 to V

DD

+0.5

Unit

Vdc

°C

°C/sec

V

Reliability

The TRU050 is capable of meeting the following qualification tests.

Table 3. Environmental Compliance

Parameter

Mechanical Shock

Mechanical Vibration

Solderability

Gross and Fine Leak

Resistance to Solvents

Conditions

MIL-STD-883, Method 2002

MIL-STD-883, Method 2007

MIL-STD-883, Method 2003

MIL-STD-883, Method 1014, 100% Tested

MIL-STD-883, Method 2016

Handling Precautions

Although ESD protection circuitry has been designed into the the TRU050, proper precautions should be taken

when handling and mounting. VI employs a human body model and a charged-device model (CDM) for ESD

susceptibility testing and design protection evaluation. ESD thresholds are dependent on the circuit

parameters used to define the model.

Table 4. ESD Ratings

Model

Human Body Model

Charged Device Model

Minimum

1500V

1000V

MIL-STD 3015

JESD 22-C101

Vectron International, 267 Lowell Rd, Unit 102, Hudson NH 03051-4916

Page 3 of 14

Tel: 1-88-VECTRON-1

•

Web:

www.vectron.com

Rev:

4/12/2016

TRU050, VCXO Based PLL

TRU050 Theory of Operation

Phase Detector

The phase detector has two buffered inputs, DATAIN and CLKIN, which are designed to switch at 1.4 volts.

DATAIN is designed to accept an NRZ data stream but may also be used for clock signals which have about a

50% duty cycle. CLKIN is connected to OUT1 or OUT2, or a divided version of one of these outputs. CLKIN

and DATAIN and are protected by ESD diodes and should not exceed the power supply voltage or ground by

more than a few hundred millivolts.

The phase detector is basically a latched flip flop/exclusive-or gate/differential amplifier filter design to produce

a DC signal proportional to the phase between the CLKIN and DATAIN signals, see figure 4 for a block

diagram and figure 5 for a open loop transfer curve. This simplies the PLL design as the designer does not

have to filter narrow pulse signal to a DC level. Under locked conditions the rising edge CLKIN will be centered

in the middle of the DATAIN signal, see figure 6.

The phase detector gain is 0.53V/rad x data density for 5volt operation, and 0.35V/rad x data density for 3.3

volt operation. Data density = 1.0 for clock signals and is system dependent on coding and design for NRZ

signals, but 0.25 could be used as a starting point for data density.

The phase detector output is a DC signal for DATAIN frequencies greater than 1MHz but produces signficant

ripple when inputs are less than 200kHz. Additional filtering is required for low input frequency applications

such as 8kHz frequency translation, see figures 8 and 9.

Under closed loop conditions the active filter has a blocking capacitor which provides a very high DC gain, so

under normal locked conditions and input frequencies >1MHz, PHO will be about V

DD

/2 and will not vary

signifigantly with changes in input frequency (within lock range). The control (voltage pin 1) will vary according

to the input frequency offset, but PHO will remain relatively constant.

Data In

(pin 7)

D

Clock In

(pin 9)

Q

1

30 kΩ

20 kΩ

D

Q

2

PHO

(pin 6)

Gain = 5 V / 2π

Gain = 2 / 3

Figure 4. Simplified Phase Detector Block Diagram

Vectron International, 267 Lowell Rd, Unit 102, Hudson NH 03051-4916

Page 4 of 14

Tel: 1-88-VECTRON-1

•

Web:

www.vectron.com

Rev:

4/12/2016

TRU050, VCXO Based PLL

V

DD

−π

V

d

V

DD

/2

0

+π

Relative

Phase (θ

e

)

0V

Gain Slope = V

DD

/ 2π

Figure 5. Open Loop Phase Detector Transfer Curve

Recovered Clock and Data Alignment Outputs

The TRU050 is designed to recover an imbedded clock from an NRZ data signal and retime it with a data

pattern. In this application, the VCXO frequency is exactly the same frequency as the NRZ data rate and the

outputs are taken off Pin 11, RCLK, and Pin 12, RDATA. Under locked conditions, the falling edge of RCLK is

centered in the RDATA pattern. Also, there is a 1.5 clock cyle delay between DATAIN and RDATA. Figure 6

shows the relationship between the DATAIN, CLKIN, RDATA and RCLK.

Data In

Data1

Clock In

Recovered

Data

Data1

Recovered Clock

Figure 6. Clock and Data Timing Relationships for the NRZ data

Other RZ encoding schemes such as Manchester or AMI can be accomidated by using a TRU050 at twice the

baud rate.

Loss of Signal, LOS and LOSIN

The LOS circuit provides an output alarm flag when the DATAIN input signal is lost. The LOS output is

normally a logic low and is set to a logic high after 256 consecutive clock periods on CLKIN with no detected

DATAIN transitions. This signal can be used to either flag external alarm circuits and/or drive the TRU050’s

LOSIN input. When LOSIN is set to a logic high, the VCXO control voltage (pin 1) is switched to an internal

voltage which centers OUT1 and OUT2 to center frequency +/-75ppm. Also, LOS automatically closes the op

amp feedback which means the op-amp is a unity gain buffer and will produce a DC voltage equal to the +op

amp voltage (pin 4), usually VDD/2.

Vectron International, 267 Lowell Rd, Unit 102, Hudson NH 03051-4916

Page 5 of 14

Tel: 1-88-VECTRON-1

•

Web:

www.vectron.com

Rev:

4/12/2016

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	Microchip
package instruction	SMD-16
Reach Compliance Code	compli

TRU050-TALGA-30M7200000

TRU050-TALGA-30M7200000 Overview

TRU050-TALGA-30M7200000 Parametric

Preview

Recommended Resources