824BP2/10-2 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > 824BP2/10-2

Preview

824BP2/10-2: Description8 Bit Programmable 2-Pole Pair Filters; File Size442KB，7 Pages; ManufacturerETC1

Download Datasheet View All

824BP2/10-2 Overview

8 Bit Programmable 2-Pole Pair Filters

Preview

Download Datasheet

View All

824BP Series

Band Pass

Description:

The 824BP Series is a 2-pole-pair digitally

programmable precision band-pass active filter that

provides high performance in a compact 2" x 2"

footprint. These new filters take advantage of the

company’s proprietary designs using surface-mount

technology to provide a low profile, compact package

in minimal board space. 824BP filters are factory

tuned to one of three factory set tuning ranges or 8-

bit custom ranges from 1 Hz to 25.6 kHz. Each filter

type features a near theoretical amplitude/phase

response along with low output voltage noise

enabling these filters to achieve a 10,000:1 or better

dynamic signal range.

Pretuned to within ±2% of the center frequency,

band-pass 824BP filters pass all frequencies lying

between the upper and lower -3dB points of the

amplitude response curve. Available Q’s for 824BP

models are 1, 2, 5, or 10.

Features/Benefits:

• Compact 2.0"L x 2.0"W footprint minimizes board

space requirements.

• Plug-in ready-to-use, reducing engineering design

and manufacturing cycle time.

• Factory tuned, no external clocks or adjustments

needed.

• Broad range of center frequencies to meet a wide

range of applications.

Applications

• Power line interference rejection

• Transducer output filtering

• Production test instrumentation

• Medical electronics equipment and research

• Comb filtering and equalization

• Noise and harmonic analysis

• RMS measurements

• Frequency spectrum analysis

8 Bit Programmable

2-Pole Pair Filters

Programmable Specifications:

. . . . . . . . . . . .Page

Digital Tuning & Control . . . . . . . . . . . . . . . . . . . . .2

Available Band-Pass Models:

824BP2

2 pole pair . . . . . . . . . . . . . . . . . . .3

General Specifications:

Ordering Information . . . . . . . . . . . . . . . . . . . . . . .4

Pin-Out/package data . . . . . . . . . . . . . . . . . . . . . .4

25 Locust St, Haverhill, Massachusetts 01830 • Tel: 800/252-7074, 978/374-0761 • FAX: 978/521-1839

e-mail: sales@freqdev.com • Web Address: http://www.freqdev.com

Product Handling

Procedure

Programmable Filter Modules Power Sequence & ESD

November 2000

Programmable Filters Modules

818, 824, 828, 828BP, 828BR, 854, 858, R854, R858

I. Scope

The following precautions are necessary when handling and installing Frequency Devices

programmable filter modules.

II. Digital Circuit Description

The digital input pins connect directly to 4000 series CMOS logic, such as the 4053 analog switch. The

power supply (Vss) for the digital logic on the module comes directly from the +15 Volt pin on the

module. This sets the threshold voltage at 11.0 V minimum to 15.0 V maximum for a "1" (High) level

and 0.0 V minimum to 4.0 V maximum for a "0" (Low) level. Applying a voltage between 4.0 and 11.0

V will produce unpredictable operation. Connecting 5 Volt or 3.3 V logic devices directly to the filter

module without using a voltage translator will result in erratic operation of the filter.

III. (VERY IMPORTANT) Power-Up and Power-Down Sequence

Do not plug-in or un-plug module while power is applied.

It is imperative that power is

supplied to the + 15 V pin on the filter module before or at the same instance that any digital pin is

pulled High (> 0.0 V). Failure to do this will result in excessive current flowing through the digital input

pin and through a protection diode internal to the 4000 logic, which will result in damage to the module.

The proper power-up and power-down sequence is:

1. Connect filter module ground.

2. Connect filter module +15 V.

3. Connect filter module -15 V.

4. Connect the input signal.

All four of the above steps can also occur simultaneously. Power-down should occur in the reverse

order.

IV. ESD Issues

Like most modern electronic equipment, the modules can be damaged by electrostatic discharge (ESD).

The modules are shipped from the factory in sealed, anti-static packaging and should be kept in the

sealed package prior to mounting on a circuit board. The following additional rules should also be

observed when handling the modules after they are removed from the factory packaging:

1. Only a person wearing a properly grounded wrist strap should handle the modules.

2. Any work surface that the modules are placed on must be properly ESD grounded.

3. Any insulating materials capable of generating static charge (such as paper) should be kept

away from the modules.

Static generating clothing should be covered with an ESD-protective smock.

25 Locust St, Haverhill, Massachusetts 01830 • Tel: 800/252-7074, 978/374-0761 • FAX: 978/521-1839

e-mail: sales@freqdev.com • Web Address: http://www.freqdev.com

Recommended Resources

New high-performance varistors, do you know?

High precision, low energy consumption timing circuit

Pressure sensor input ML2200/2208 circuit

FM radio receiving host

Position control method using potentiometer (circuit diagram)

Computer motherboard circuit diagram 430TX_10

EEWORLD University ---- C2000 DesignDRIVE series courses: C2000 DesignDRIVE series courses : https://training.eeworld.com.cn/course/3847...; hi5 MCU

How can I read the model and main parameters of the graphics card and other hardware information in XP system? (Not reading from Windows): How can I read the model and main parameters of the graphics card and other hardware information in XP system? (Not reading from Windows)...; wfdx022 Embedded System

What is the problem with Error initializing emulator when emulating with CCS4.1?: I reinstalled the software and the driver, why is it still like this?...; 懒虫 DSP and ARM Processors

Contest entries submitted to Environmental Monitoring Terminal: Environmental monitoring terminalAuthor: JohnBrief introduction of the work (100-200 words) (Design name, work photo, function introduction, etc.)This project is an environmental monitoring terminal t...; John20190401 DigiKey Technology Zone

TI Chief Scientist Fang Jin——What is new with SoCs: 最近工作需要用到，找到一份资料与大家分享下[b]What is new with SoCs[/b]By Gene FrantzTI Principal Fellow and Business Development Manager, DSPAnother comment we received recently was from Shreshtha Kumar, questioning all o...; clark DSP and ARM Processors

STM32 driver MAX7219 failed, help: I used stm32 to drive the MAX7219 module. I found that the module had different power-on behaviors at different times, and the behaviors were different when the emulator was plugged in or not. I had p...; shijizai stm32/stm8

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components