VTM3-C22E-16M376 datasheet, PDF

Datasheet> All Categories > Passive components> oscillator> VTM3-C22E-16M376

VTM3-C22E-16M376: DescriptionClipped Sine Output Oscillator, 16.376MHz Nom, ROHS COMPLIANT, HERMETIC SEALED, CERAMIC, SMD, 4 PIN; CategoryPassive components oscillator; File Size207KB，8 Pages; ManufacturerMicrosemi; Websitehttps://www.microsemi.com; Environmental Compliance

Download Datasheet Parametric View All

VTM3-C22E-16M376 Overview

Clipped Sine Output Oscillator, 16.376MHz Nom, ROHS COMPLIANT, HERMETIC SEALED, CERAMIC, SMD, 4 PIN

VTM3-C22E-16M376 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	Microsemi
package instruction	ROHS COMPLIANT, HERMETIC SEALED, CERAMIC, SMD, 4 PIN
Reach Compliance Code	compli
Other features	TAPE AND REEL
Ageing	1 PPM/YEAR
Maximum control voltage	2.5 V
Minimum control voltage	0.5 V
Frequency Adjustment - Mechanical	NO
Frequency offset/pull rate	8 ppm
frequency stability	2%
JESD-609 code	e4
Installation features	SURFACE MOUNT
Nominal operating frequency	16.376 MHz
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Oscillator type	CLIPPED SINE
Output impedance	10000 Ω
Output level	0.8 V
physical size	3.2mm x 2.5mm x 1.0mm
Maximum supply voltage	3.15 V
Minimum supply voltage	2.85 V
Nominal supply voltage	3 V
surface mount	YES
Terminal surface	Gold (Au) - with Nickel (Ni) barrie

Preview

Download Datasheet

View All

VTM3 series

Voltage Controlled Temperature Compensated Crystal Oscillator

Features

•

Small 3.2x2.5 package size

•

Clipped Sine Wave Output

•

Output Frequencies to 45 MHz

•

Fundamental Crystal Design

•

Optional VCXO Function available

•

Gold over nickel contact pads

•

Hermetically Sealed Ceramic SMD package

The VTM3, VCTXCO

•

Product is compliant to RoHS directive

and fully compatible with lead free assembly

Applications

•

GPS

•

WiMAX, Wi-Fi, Wi-LAN

•

Seismic Exploration

•

Point to point radios

•

Broadband Access

•

Test Equipment

•

PDA’s

Description

Vectron’s VTM3 Temperature Compensated

Crystal Oscillator (TCXO) is a quartz stabilized,

clipped sine wave output, analog temperature

compensated oscillator, operating off either a

2.8, 3.0, or 3.3 volt supply.

Vectron International: 267 Lowell Road, Suite 102, Hudson NH 03051

Tel: 1-88-VECTRON-1

e-mail: vectron@vectron.com

Recommended Resources

Thyristor silicon stack protection circuit a

HF4-28-50 diesel engine voltage regulating circuit

Stage strobe and photo flash dual-purpose light circuit

Non-inverting composite DC amplifier circuit

Computer motherboard circuit diagram 440BX_33

Computer motherboard circuit diagram 815 5_27

Simple function demonstration video: [media=x,500,375]http://www.tudou.com/programs/view/0RLwpuRQq64[/media] AM335X internship training PDF which talks about the performance of AM335X and some examples of application test [[i] This post ...; PENGSHIFANG DSP and ARM Processors

Analysis of Linux Kernel IP Queue Mechanism (Part 3) - Analysis of ip_queue Kernel Module: Preface This article and three others will analyze the IP Queue mechanism from user-mode applications to kernel-mode module programming. The titles of the three articles are: Analysis of the Linux Ker...; fish001 Linux and Android

Why does the transistor loss in the OCL circuit increase with increasing frequency?: The circuit is shown in the figure. The front-stage transistors of the OCL circuit are: NPN-PBSS8110Y, PNP-PBSS9110Y. The models of the rear-stage transistors are: NPN-NSS1C301ET4G, PNP-NSS1C300ET4G. ...; 咖啡不加冰 Analog electronics

[Ask] SuperIO watchdog issue: I am working on the software side of a hardware project and now I have a problem that I would like to ask for a solution. A motherboard is connected to an MCU, which controls the voltage regulation or...; fengboning Embedded System

DCDC ripple experiment: Notes on using an oscilloscope to test rippleMeasure using the AC coupling mode of the oscilloscopeBecause the oscilloscope head cover is easy to introduce noise, the probe head cover must be removed ...; 灞波儿奔 Analogue and Mixed Signal

Solution to the problem of automatic restart of the target board when debugging the UP-TECH2410 board with JLINK: The problem is this: About a month ago, I built a S3C2410 project on IAR6.1. I have two boards, one FS2410 board from Youlong and two UP-TECH2410 boards from Broadcom. There are two debuggers for that...; zsjalive Integrated technical exchanges

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components