UL62H256BSK55 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > storage> storage> UL62H256BSK55

UL62H256BSK55: DescriptionStandard SRAM, 32KX8, 55ns, CMOS, PDSO28, 0.300 INCH, SOP-28; Categorystorage storage; File Size87KB，10 Pages; ManufacturerSimtek; Websitehttp://www.simtek.com

Download Datasheet Parametric View All

UL62H256BSK55 Overview

Standard SRAM, 32KX8, 55ns, CMOS, PDSO28, 0.300 INCH, SOP-28

UL62H256BSK55 Parametric

Parameter Name	Attribute value
Maker	Simtek
package instruction	SOP,
Reach Compliance Code	unknow
ECCN code	EAR99
Maximum access time	55 ns
JESD-30 code	R-PDSO-G28
JESD-609 code	e0
length	17.9 mm
memory density	262144 bi
Memory IC Type	STANDARD SRAM
memory width	8
Number of functions	1
Number of terminals	28
word count	32768 words
character code	32000
Operating mode	ASYNCHRONOUS
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
organize	32KX8
Package body material	PLASTIC/EPOXY
encapsulated code	SOP
Package shape	RECTANGULAR
Package form	SMALL OUTLINE
Parallel/Serial	PARALLEL
Peak Reflow Temperature (Celsius)	NOT SPECIFIED
Certification status	Not Qualified
Maximum seat height	2.65 mm
Maximum supply voltage (Vsup)	2.7 V
Minimum supply voltage (Vsup)	2.3 V
Nominal supply voltage (Vsup)	2.5 V
surface mount	YES
technology	CMOS
Temperature level	INDUSTRIAL
Terminal surface	TIN LEAD
Terminal form	GULL WING
Terminal pitch	1.27 mm
Terminal location	DUAL
Maximum time at peak reflow temperature	NOT SPECIFIED
width	7.5 mm

Preview

Download Datasheet

View All

UL62H256B

Low Voltage Automotive Fast 32K x 8 SRAM

Features

32768 x 8 bit static CMOS RAM

35 and 55 ns Access Time

Common data inputs and

Description

address change, the data outputs

go High-Z until the new information

is available. The data outputs have

no preferred state. The Read cycle

is finished by the falling edge of W,

or by the rising edge of E, respec-

tively.

Data retention is guaranteed down

to 1.5 V. With the exception of E, all

inputs consist of NOR gates, so

that no pull-up/pull-down resistors

are required.

The UL62H256B is a static RAM

manufactured using a CMOS pro-

cess technology with the following

operating modes:

data outputs

- Read

- Standby

Three-state outputs

- Write

- Data Retention

Typ. operating supply current

The memory array is based on a

35 ns: 45 mA

6-Transistor cell.

55 ns: 30 mA

Standby current < 30 µA at 125 °C The circuit is activated by the fal-

ling edge of E. The address and

Power supply voltage 2.5 V

control inputs open simultaneously.

Operating temperature range

According to the information of W

-40 °C to 85 °C

-40 °C to 125 °C

and G, the data inputs, or outputs,

are active. In a Read cycle, the

CECC 90000 Quality Standard

data outputs are activated by the

ESD protection > 2000 V

falling edge of G, afterwards the

(MIL STD 883C M3015.7)

data word will be available at the

Latch-up immunity >100 mA

outputs DQ0-DQ7. After the

Package: SOP28 (300/330 mil)

Pin Configuration

Pin Description

A14

A12

DQ0

DQ1

DQ2

VSS

VCC

A13

A11

A10

DQ7

DQ6

DQ5

DQ4

DQ3

Signal Name

A0 - A14

DQ0 - DQ7

VCC

VSS

Signal Description

Address Inputs

Data In/Out

Chip Enable

Output Enable

Write Enable

Power Supply Voltage

Ground

SOP

Top View

November 26, 2002

Recommended Resources

Electronic music flashing light circuit

TOPSwitch application circuit in PFC circuit 03

Clamp amplifier AD8037PIN diode driver circuit

Dual tone dial phone lock zero circuit circuit diagram

Stereo transmitter circuit without phase-locked loop frequency stabilization

split phase amplifier circuit

ADC12 problem with MSP430: Please explain it to me in your own words, thank you.1. How to understand sampling, holding, and conversion?(1) Since ADC12 is 12 bits, is the number of sampling points 4096 during sampling?(2) Keep t...; ajungle Microcontroller MCU

Problems caused by SD card upgrade: I used an SD card to upgrade my machine, and found that there was a certain probability of the following problem: After the upgrade was completed, the system would freeze at OEM Launch when restarting...; 沧海蝴蝶 Embedded System

Discussion on Dual Power Supply: I've been learning about DSP recently, using 2812. During the learning process, I found some special requirements for its dual power supply. When powered on, the core is powered on first, then the I/O...; koday22 DSP and ARM Processors

Is it related to the watchdog setting that the microcontroller program sometimes crashes?: Program; PCON EQU 087H; Power control register; mov auxr, #1; Disable the pulse output of the ALE pin. Note that there is a semicolon in front. Does it mean a comment? Or a command? In addition, is th...; 一无所知 Embedded System

Implementing CIMT Coding with FPGA: I am working on a project recently, which is to use FPGA to realize video transmission over optical fiber. Since ordinary binary code cannot be transmitted in optical fiber, the binary code must be co...; ckwangwei FPGA/CPLD

Notes on the power consumption test of LM3S5749: A note based on the power consumption test of LM3S5749. It contains some experimental data and a brief introduction to some methods of controlling power consumption....; eeleader Microcontroller MCU

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components