AFBR-1012 Transmitter and AFBR-2012 Receiver are de-
signed to transmit/ receive up to 25MBit/s optical data
which are biphase coded (up to 50Mbaud). Both are
packaged in 4-pin transfer molded, low-cost packages
ready for assembly into MOST® plastic fiber optic connec-
tor receptacles.
The transmitter utilizes a 650 nm LED source with inte-
grated optics for efficient coupling into 1mm Polymer Op-
tical Fiber (POF), and the receiver contains a high speed
PIN diode to receive this light.
Input/output data has TTL switching levels, compatible
with MOST® Network Interface Controller ICs.
These optical components are specified for operation
over a -40°C to +95°C temperature range, and meet the
reliability requirements of automotive applications. In the
absence of data activity, the receiver switches to very low
power mode. While in this mode, the PIN diode can sense
new data activity and switch the receiver back to full op-
eration.
Features
Operating @ 3.3V or 5V (+/-5% each) Power supply
Operating temperature range -40°C to +95°C
TTL Data Input/ Output (Logic to Light Function)
Power down mode
During the low power mode a receiver STATUS-pin
indicates if modulated light is received (Light on ->
STATUS = low). The power supply of the whole MOST
device can be switched on with this Status-pin.
Duty Cycle Adjust (DCA), yields to enhanced SP1 input
range
650nm for working in a low attenuation range of PMMA
Fiber
-25dBm guaranteed sensitivity @ 650nm
Fully compliant to “MOST® Specification of Physical
Layer Rev 1.1”
RoHS compliant (Lead free and halogen free)
Lead is flash gold
Low power consumption
Photo current sensing, network activity detection and
Low Power Mode (I
CC
< 10μA)
Additional Low Power Mode (I
CC
< 15μA) for the
transmitter when SP1 input is low
Signal detect and Status Output
Pulse width control
Applications
Optical Transmitter and Receiver for MOST® 50 Mbaud
systems (a full description of the MOST® 50 Mbaud
system is available at www.mostcooperation.com)
Absolute maximum ratings
Parameter
Supply Voltage
[1]
Storage Temperature
Soldering Temperature
(distance to package >3mm; t≤10s)
[2]
Voltage at any PIN
Electrostatic Voltage Capability
[3]
ESD
Symbol
V
CCMax
T
STG
T
S
Min.
-0.5
-40
Max.
6.0
110
260
Units
V
°C
°C
V
kV
-0.5
VCC+0.5
2.0
Notes:
1. Maximum supply voltage without causing damage
2. For more information regarding the solder process see Application Note 5420 (Handling, Storage, Operating and Processing)
3. ESD Capability for all Pins HBM (human body model) according JESD22-A114B
Recommended operating conditions
Parameter
Supply Voltage low
Supply Voltage high
Operating temperature (ambient)
[1]
Symbol
V
CC_l
V
CC_hl
T
A
Min.
3.135
4.75
-40
Max.
3.465
5.25
95
Units
V
V
°C
Notes:
1. For more information see Application Note 5420 (Handling, Storage, Operating and Processing)
All the data in this specification refers to the operating conditions above and over lifetime unless otherwise stated.
Part Number Options
Part Number
AFBR-1012S/AFBR-2012S
AFBR-1012L/AFBR-2012L
AFBR-1012M/AFBR-2012M
Part Description
Transmitter/Receiver – Short Leads
Transmitter/Receiver – Long Leads
Transmitter/Receiver - Medium Leads
Solder Heat Resistance
Lead dip in liquid solder of 260°C for 10 Sec.
acc. JEDEC standard JESD22-B106-C
(for more information see Application Note 5420)
2
AFBR-1012 (Transmitter)
DC Characteristics
Parameter
Low Level Input voltage
High Level Input Voltage
Input Leakage Current
(VCC = 5.0V; VI = 0V or VI =5.0V)
Input Capacitance
Input Resistance
Supply Current Full Power Mode
[1]
Supply Current Low Power Mode
[2]
Symbol
V
IL
V
IH
I
L
C
I
R
I
I
CC
I
LP2
Min.
-0.3
2.0
Typ.
Max.
0.8
VCC+0.3
+/-20
7
Units
V
V
μA
pF
kΩ
mA
μA
2
25
15
Notes:
1. The current through the LED and therefore the optical output power and overall power consumption depends on the settings of R
EXT
.
The nominal value for R
EXT
is 15k. With R
EXT
= 30k the optical output power is about -3dB of the nominal value.
Important: The external resistor of R
EXT
must be within the range of 13.5kΩ to 33kΩ. For values out of this range functionality may not be given over the
whole temperature range and the device lifetime.
2. If the transmitter is in full power mode it is switched OFF 1ms (max) after Tx DATA is low. If the transmitter is in low power mode it is switched ON
6ms (max) after Tx Data transmission starts.
AC Electrical Characteristics
Parameter
Power Up Time
Data Power Down Time
Symbol
T
PU
T
PD
Min.
Typ.
0.016
0.01
Max.
6
1.0
Units
ms
ms
Optical Signal Characteristics 45.158Mbaud (44.1kHz)
(22.5 MBit/s MOST Data, V
CC
= 3.135 … 3.465V or 4.75 … 5.25V, R
EXT
= 15kOhm)
Parameter
Peak wavelength
Temperature coefficient λPEAK
Spectral Bandwidth (FWHM)
Average Output Power coupled into plastic fiber
[1]
Average Output Power coupled into plastic fiber
(if R
EXT
= 13.5k is used instead of R
EXT
=15k)
[1]
Optical Output Power “Light off ”
[2]
Optical Rise Time (20% - 80%)
[4]
Optical Fall Time (80% - 20%)
[4]
Extinction Ratio
[4,6]
Pulse Width Variation
[3,4,5]
Average Pulse Width Distortion
[3,4]
Data Dependent Link Jitter
[3,4]
Uncorrelated Link Jitter
[3,4]
Positive Overshoot within 0UI … 2/3UI
[4,6]
Negative Overshoot within -1UI … -1/4UI
[4,6]
High Level Signal Ripple between 2/3UI and 3/4UI
Symbol
λ
Peak
TC
λ
Delta
λ
P
opt
P
opt
P
OFF
t
r
t
f
r
e
t
PWV
t
APWD
t
DDJ
t
UJ
Min.
630
Typ.
650
0.16
20
Max.
685
30
-2.0
-1.5
-50
Units
nm
nm/K
nm
dBm
dBm
dBm
ns
ns
dB
ns
ns
ns
ns
%
%
%
-8.0
-7.5
-5.2
-4.7
2.5
3.5
10
20.0
-1.4
0.2
0.05
-20
-10
-10
15
5.98
5.98
24.29
1.4
0.77
0.33
40
20
10
Notes:
1. Average value when transmitting modulated light @signal timing parameters. The output power coupled into plastic fiber Popt is measured with
a large area detector at the end of 30cm POF fiber with a NA = 0.5 which is ideally coupled to the transmitter
2. Average value when signal on Tx_Data is low
3. The electrical input signal has to fulfill the following requirements: t
pwv(min)
= 20.1ns, t
pwv(max)
= 24.1ns, t
tAPWD(min)
= -1.5ns and t
tAPWD(max)
=
1.5ns, t
DDJ(max)
= 0.22ns, t
UJ(max)
= 0.10ns
4. Characterized with Avago Characterization Boards
5. Limits for 2UI are 42.2 … 46.4ns and for 3UI they are 64.3 … 68.5ns.
6. Top and Base level measured at least over 10UIs.
3
Optical Signal Characteristics 49.152Mbaud (48kHz)
(24.576 MBit/s MOST Data, V
CC
= 3.135 … 3.465V or 4.75 … 5.25V, R
EXT
= 15k)
Parameter
Peak wavelength
Temperature coefficient λPEAK
Spectral Bandwidth (FWHM)
Average Output Power coupled into plastic fiber
[1]
Average Output Power coupled into plastic fiber
(if R
EXT
= 13.5k is used instead of R
EXT
=15k)
[1]
Optical Output Power “Light off ”
[2]
Optical Rise Time (20% - 80%)
[4]
Optical Fall Time (80% - 20%)
[4]
Extinction Ratio
[4,6]
Pulse Width Variation
[3,4,5]
Average Pulse Width Distortion
[3,4]
Data Dependent Link Jitter
[3,4]
Uncorrelated Link Jitter
[3,4]
Positive Overshoot within 0UI … 2/3UI
[4,6]
Negative Overshoot within -1UI … -1/4UI
[4,6]
High Level Signal Ripple between 2/3UI and 3/4UI
Symbol
λ
Peak
TC
λ
Delta
λ
P
opt
P
opt
P
OFF
t
r
t
f
r
e
t
PWV
t
APWD
t
DDJ
t
UJ
Min.
630
Typ.
650
0.16
20
Max.
685
30
-2.0
-1.5
-50
Units
nm
nm/K
nm
dBm
dBm
dBm
ns
ns
dB
ns
ns
ns
ns
%
%
%
-8.0
-7.5
-5.2
-4.7
2.5
3.5
10
18.4
-1.28
0.2
0.05
-20
-10
-10
15
5.49
5.49
22.3
1.28
0.71
0.31
40
20
10
Notes:
1. Average value when transmitting modulated light @signal timing parameters. The output power coupled into plastic fiber Popt is measured with
a large area detector at the end of 30cm POF fiber with a NA = 0.5 which is ideally coupled to the transmitter
2. Average value when signal on Tx_Data is low
3. The electrical input signal has to fulfill the following requirements: t
pwv(min)
= 18.4ns, t
pwv(max)
= 22.3ns, t
tAPWD(min)
= -1.28ns and t
tAPWD(max)
=
1.28ns, t
DDJ(max)
= 0.2ns, t
UJ(max)
= 0.09ns
4. Characterized with Avago Characterization Boards
5. Limits for 2UI are 38.72 … 42.66ns and for 3UI they are 59.06 … 63.01ns.
6. Top and Base level measured at least over 10UIs.
[align=left][color=rgb(0, 0, 0)][font=Tahoma, Helvetica, SimSun, sans-serif, Hei]The National Aeronautics and Space Administration (NASA) released a global air quality map in September 2010, specifica...
430F42x has many LCD output ports S0-S96..., which are written on page P140 in Wei Xiaolong's "MSP430 Series MCU Interface Technology and System Design Examples": LCD output ports can also be configur...
I read the readme document of 2440_usb_driver (S3C2410X USB downloader Installation Guide Release 1.11) which says to first burn u2440amon.bin (1) Program the u241mon.bin into the flash memory of SMDK...
I'm working on an audio signal analyzer recently and I used the fft IP core but I can't always get the results.
Below I use it to control the state machine of the fft core, and the simulation waveform...
Case BackgroundWith the development of Industry 4.0, the degree of industrial automation continues to improve. To realize Industry 4.0, a high degree of industrialization and automation is required. I...
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
Sailing is gaining more and more attention. How to use modern technology to assist training and improve competition results is particularly important. Considering the real-time data collection in t...[Details]
introduction
my country has a vast territory and a large population. The scale of housing construction is huge, and the amount of residential construction is large and wide. It is still on t...[Details]
1 Introduction
The high temperature tester is mainly used for temperature tracking measurement and data acquisition during the heating process. By systematically analyzing the test data, the...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
Abstract: In order to generate a stable excitation signal, the design of a digital frequency synthesizer is implemented on FPGA using Verilog hardware language. The design includes accumulator, wav...[Details]
1 Introduction
As an emerging microfabrication technology, micro-electromechanical system (MEMS) technology has begun to be applied in various fields. It can integrate functions such as inform...[Details]
1. With the development of modern industry and the continuous improvement of automation, some medium and large control systems have been greatly facilitated, which not only makes control easier, bu...[Details]
LED lamps and bulbs are now rapidly replacing incandescent, halogen and CFL (compact fluorescent lamp) light sources in many general lighting applications. Flyback DC/DC converters are the power su...[Details]
Flooded Batteries
This battery developed in Germany can be used to power flashlights, strobe lights and toys as long as it is filled with water. This battery can be stored for 50 years and can...[Details]
The potentiometer is an adjustable electronic component. The main functions of the potentiometer in the circuit are as follows:
1. Used as a voltage divider
A potentiometer is a continuou...[Details]
Experimental tasks
A DS18B20 is used to form a temperature measurement system. The temperature measurement accuracy reaches 0.1 degrees. The temperature range is between -20 degrees and +50 de...[Details]
This controller uses PIC16C54 single-chip microcomputer as the controller, and it is very easy to use: just connect a telephone line to the loudspeaker through the controller, and you can rem...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
