EEWORLDEEWORLDEEWORLD

Part Number

Search

B13A1H-JH

Description
TOGGLE SWITCH,STRAIGHT,SPDT,ON-ON,PC TAIL TERMINAL,TOGGLE BAT,7
Categoryunclassified   
File Size256KB,8 Pages
ManufacturerOhmite
Websitehttps://www.ohmite.com
Download Datasheet Parametric View All

B13A1H-JH Overview

TOGGLE SWITCH,STRAIGHT,SPDT,ON-ON,PC TAIL TERMINAL,TOGGLE BAT,7

B13A1H-JH Parametric

Parameter NameAttribute value
Lead-freeYes
EU RoHS regulationsYes
stateACTIVE
terminal coatingGOLD OVER NICKEL
Manufacturer SeriesB
Switch typeTOGGLE SWITCH
Series B
Toggles
Process Sealed Subminiature Antistatic Toggles
A
General
Specifications
Electrical Capacity (Resistive Load)
Logic Level:
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Pushbuttons
Rockers
Other Ratings
Programmable Illuminated PB
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Keylocks
Contact Timing:
Angle of Throw:
50 milliohms maximum
500 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
100,000 operations minimum for On-None-On & On-Off-On
50,000 operations minimum for other circuits
50,000 operations minimum for locking lever models
50,000 operations minimum
Toggles A, A1, E & K with Long Paddle: 1.47N (momentary); 1.18N (maintained)
Toggles J & H & K with Short Paddle: 2.72N (momentary); 1.84N (maintained)
Toggle L: 0.59N
Nonshorting (break-before-make)
26°
Materials & Finishes
Rotaries
Toggle:
Bushing:
Gasket:
Case Housing:
Support Bracket:
Movable Contact:
Stationary Contacts:
Terminals:
Nickel plated brass
Carbon blended polyamide; nickel plated zinc alloy for locking levers & threaded bushing
Nitrile butadiene rubber
Glass fiber reinforced polyamide
Tin plated phosphor bronze
Phosphor bronze with gold plating
Copper alloy with gold plating
Copper alloy with gold plating
Tactiles
Slides
Environmental Data
Operating Temperature Range:
Humidity:
Vibration:
Shock:
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
2
) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Tilt
Touch
Installation
Mounting Torque:
.30 ~ .45Nm (2.65 ~ 3.98 lb
in) for A1 actuator with threaded bushing only
PCB Processing
Indicators
Soldering:
Cleaning:
Wave Soldering Recommended: See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
Automated cleaning. See Cleaning specifications in Supplement section.
Accessories
Standards & Certifications
Flammability Standards:
Supplement
UL94V-0 available
The B Series toggles have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
A12
www.nkk.com
[Application development based on NUCLEO-F746ZG motor] 10. Parameter configuration - GPIO port configuration
The common GPIO ports used on the development board are 4 LEDs, 1 button, and 3 enable pins U, V, and W. The Hall sensor is not used yet, so it is omitted. 1. Hardware circuit design (1) Three enable ...
annysky2012 Motor Drive Control(Motor Control)
IAR is running but MBED is not showing any effect + [ST Theme Month]
I received the board a few days ago. I first experimented with MBED, thinking it would be very simple. However, I faced several problems: 1. What board to choose? There is no L011K4 on the Internet. I...
wbhb2011 stm32/stm8
Connection between Bluetooth module HC-05 and 51 microcontroller
[i=s]This post was last edited by Jacktang on 2020-11-4 07:41[/i]Experimental resultsAfter installing the HC-PDA-ANDROID.apk software on the phone, the system is turned on. The phone can search for th...
Jacktang Wireless Connectivity
Integrated circuit testing knowledge
1. Before testing, you need to understand the working principle of the integrated circuit and its related circuits. Before checking and repairing the integrated circuit, you must first be familiar wit...
zzzzer16 Test/Measurement
Please help me figure out what's going on.
Why when I use MDK and ULINK ME to download the program, the following error message appears: Error: Flash Download failed-Target DLL has been cancelled.[img]1[/img] Urgent help, if anyone knows pleas...
wanghongyang stm32/stm8
What are the problems encountered when the kernel of the virtual machine LINUX is different from that of the development board?
1. Does anyone know that the Linux kernel in the virtual machine is 2.4, and the system on the ARM9 learning board is 2.6. So can the compiled file be executed on the development board? 2. Kernel tran...
zhiha258 Linux and Android

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1357  376  290  1743  241  28  8  6  36  5 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号