Dear experts: I would like to ask for advice on a microcontroller control problem. The figure is a schematic diagram. A load powered by a DC battery, if the load is successfully started once, the batt...
I recently wanted to make a single-ended input and dual-ended output circuit. My initial plan was to connect two inverting amplifiers in series, as shown in the figure:Later, I looked up a circuit:I t...
I am currently involved in a car driving recorder project and I am eager to get an msp430 development board to support the project. I am currently in the beginner stage and hope to be able to communic...
[table=98%] [tr][td][float=right] [/float] I am a newbie. Some time ago, I suddenly thought of using a 6-digit digital tube to make a simple electronic clock that displays seconds, minutes, and hours....
I have designed a version of the expansion board for the BB board before, [url]https://bbs.eeworld.com.cn/thread-376965-1-1.html[/url], and the pins of the BB board and the BBB board are exactly the s...
I would like to ask if I do not process the serial port receiving and sending in the interrupt, but do it in the main program. I know that if I want to determine whether the serial port has received a...
This program is written to simulate the serial port hardware mechanism. When used, a timed interrupt can be set with a time interval of 1/4 baud rate. The receiving function is called once for ea...[Details]
When the WDP500-2A plane grating monochromator is used to test the emission wavelength of a high-power laser diode at different currents, the matching of the laser diode has the disadvantages of lo...[Details]
DSP (digital signal processor) is used more and more frequently in today's engineering applications. There are three main reasons for this: first, it has powerful computing power and is capable of ...[Details]
0 Introduction
With the rise and continuous improvement of the solid-state lighting industry, light-emitting diodes (LEDs) have become an alternative lighting technology and are gr...[Details]
Capacitors
are basic components in various electronic devices and are widely used for bypassing, coupling,
filtering
, tuning, etc. in electronic circuits. However, to use capacitors,...[Details]
introduction
MEMS is a high-tech that has flourished on the basis of integrated circuit production technology and dedicated micro-electromechanical processing methods. Pressure sensors develop...[Details]
introduction
At present, the research on micron and nanotechnology is very active, which has led to the rapid development of microtechnology and micro-mechanical electronic system (MEMS) t...[Details]
1 Overview
In the field of traditional lighting, the concepts and definitions of lamps and lamps are clear. Lamps and lamps have their own applicable product standards, supporting technical st...[Details]
The production process of lithium batteries does not mention the previous processes such as material preparation, winding, liquid injection, and packaging, but only talks about the final formation ...[Details]
summary
This article will briefly analyze the success and shortcomings of high-frequency DC-DC switching power supplies in the process of miniaturization (the second basic goal), and propose m...[Details]
1. Tips for charging UPS for the first time
After purchasing a new UPS, plug the UPS into the 220V mains power grid and charge it for at least 12 hours to ensure that the battery is fully char...[Details]
HL201A is a special thick film driver integrated circuit with a capacity of less than 75AGTR developed by Xi'an Power Electronics Technology Research Institute. The article explains the pin arrange...[Details]
1. Brief Introduction
With the continuous development and improvement of single-chip microcomputer technology, single-chip microcomputers have been widely used in all walks of life, and ...[Details]
In some motion control systems with simple control or low cost requirements, stepper motors are often used as actuators. The biggest advantage of stepper motors in such applications is that they ca...[Details]
As we all know, the manufacturing of modern automobiles is divided into four major processes: stamping, welding, painting and assembly, and the powertrain constitutes five inseparable production pr...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
