B2RJH-GC datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > unclassified> B2RJH-GC

B2RJH-GC: DescriptionTOGGLE SWITCH,STRAIGHT,SPDT,ON-ON,PC TAIL TERMINAL,TOGGLE BAT,7; Categoryunclassified; File Size256KB，8 Pages; ManufacturerOhmite; Websitehttps://www.ohmite.com

Download Datasheet Parametric View All

B2RJH-GC Overview

TOGGLE SWITCH,STRAIGHT,SPDT,ON-ON,PC TAIL TERMINAL,TOGGLE BAT,7

B2RJH-GC Parametric

Parameter Name	Attribute value
Lead-free	Yes
EU RoHS regulations	Yes
state	ACTIVE
terminal coating	GOLD OVER NICKEL
Manufacturer Series	B
Switch type	TOGGLE SWITCH

Preview

Download Datasheet

View All

Series B

Toggles

Process Sealed Subminiature Antistatic Toggles

General

Specifications

Electrical Capacity (Resistive Load)

Logic Level:

0.4VA maximum @ 28V AC/DC maximum

(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)

Note: Find additional explanation of operating range in Supplement section.

Pushbuttons

Rockers

Other Ratings

Programmable Illuminated PB

Contact Resistance:

Insulation Resistance:

Dielectric Strength:

Mechanical Life:

Electrical Life:

Nominal Operating Force:

Keylocks

Contact Timing:

Angle of Throw:

50 milliohms maximum

500 megohms minimum @ 500V DC

500V AC minimum for 1 minute minimum

100,000 operations minimum for On-None-On & On-Off-On

50,000 operations minimum for other circuits

50,000 operations minimum for locking lever models

50,000 operations minimum

Toggles A, A1, E & K with Long Paddle: 1.47N (momentary); 1.18N (maintained)

Toggles J & H & K with Short Paddle: 2.72N (momentary); 1.84N (maintained)

Toggle L: 0.59N

Nonshorting (break-before-make)

26°

Materials & Finishes

Rotaries

Toggle:

Bushing:

Gasket:

Case Housing:

Support Bracket:

Movable Contact:

Stationary Contacts:

Terminals:

Nickel plated brass

Carbon blended polyamide; nickel plated zinc alloy for locking levers & threaded bushing

Nitrile butadiene rubber

Glass fiber reinforced polyamide

Tin plated phosphor bronze

Phosphor bronze with gold plating

Copper alloy with gold plating

Tactiles

Slides

Environmental Data

Operating Temperature Range:

Humidity:

Vibration:

Shock:

–30°C through +85°C (–22°F through +185°F)

90 ~ 95% humidity for 96 hours @ 40°C (104°F)

10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning

in 1 minute; 3 right angled directions for 2 hours

50G (490m/s

) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)

Tilt

Touch

Installation

Mounting Torque:

.30 ~ .45Nm (2.65 ~ 3.98 lb

•

in) for A1 actuator with threaded bushing only

PCB Processing

Indicators

Soldering:

Cleaning:

Wave Soldering Recommended: See Profile A in Supplement section.

Manual Soldering: See Profile A in Supplement section.

Automated cleaning. See Cleaning specifications in Supplement section.

Accessories

Standards & Certifications

Flammability Standards:

Supplement

UL94V-0 available

The B Series toggles have not been tested for UL recognition or CSA certification.

These switches are designed for use in a low-voltage, low-current, logic-level circuit.

When used as intended in a logic-level circuit, the results do not produce hazardous energy.

A12

www.nkk.com

Recommended Resources

Do you know about 600V small smart power devices?

Remote transmitter circuit diagram

Driving DC motor circuits with AC power

Touch power supply circuit diagram 2 composed of L200

High power HF band standing wave meter/power meter

Automatic sentence playback circuit

Accuracy? Resolution? Arc Minutes? How to Manage Your Motor Control Design: Imagine driving to work this morning: the traffic light turns green, you immediately step on the accelerator, and the car responds quickly within a few seconds and continues to drive to work. This pro...; qwqwqw2088 Analogue and Mixed Signal

Notice on Issuing the List of Integrated Circuit Design Enterprises (Third Batch): The competent departments of information industry in all provinces, autonomous regions, municipalities directly under the Central Government and cities with independent planning status:According to th...; fighting Analog electronics

Driver loading failed, help!: Write a simple driver mydriver.dll under wince5.0. When loading the module, the following appears: ... 4294769776 PID:3f96bca TID:3fa0f9a 0x83fca800: >>> Loading module mydriver.dll at address 0x03010...; weiyujuan Embedded System

How to disable the operation of the lower window of the messagebox prompt box?: As the title says, I solved the problem of how to prevent the messagebox from being covered yesterday. Today I encountered the problem that after the messagebox prompt box appears, I can still operate...; 378903745 Embedded System

How to remove click screen sound: How to change the sound of clicking the screen in EVC by modifying the program. I modified the registry, but it didn't work. . The code is as follows. HKEY hKey1; DWORD dwType1; DWORD dwScreen1 = 1; D...; kccch Embedded System

WinCE5 implements PPPOE dial-up, which modules and registry need to be configured in the kernel?: As the title says, I have added Ras/PPP, PPPoE, Tapi, etc., and createdin . When dialing, it prompts: Remote concentrator is not responding... I captured the packets and compared them with the PC. I f...; qiyuan775 Embedded System

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components