EEWORLDEEWORLDEEWORLD

Part Number

Search

B2SJH-JH

Description
TOGGLE SWITCH,STRAIGHT,SPDT,ON-ON,PC TAIL TERMINAL,TOGGLE BAT,7
Categoryunclassified   
File Size256KB,8 Pages
ManufacturerOhmite
Websitehttps://www.ohmite.com
Download Datasheet Parametric View All

B2SJH-JH Overview

TOGGLE SWITCH,STRAIGHT,SPDT,ON-ON,PC TAIL TERMINAL,TOGGLE BAT,7

B2SJH-JH Parametric

Parameter NameAttribute value
Lead-freeYes
EU RoHS regulationsYes
stateACTIVE
terminal coatingGOLD OVER NICKEL
Manufacturer SeriesB
Switch typeTOGGLE SWITCH
Series B
Toggles
Process Sealed Subminiature Antistatic Toggles
A
General
Specifications
Electrical Capacity (Resistive Load)
Logic Level:
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Pushbuttons
Rockers
Other Ratings
Programmable Illuminated PB
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Keylocks
Contact Timing:
Angle of Throw:
50 milliohms maximum
500 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
100,000 operations minimum for On-None-On & On-Off-On
50,000 operations minimum for other circuits
50,000 operations minimum for locking lever models
50,000 operations minimum
Toggles A, A1, E & K with Long Paddle: 1.47N (momentary); 1.18N (maintained)
Toggles J & H & K with Short Paddle: 2.72N (momentary); 1.84N (maintained)
Toggle L: 0.59N
Nonshorting (break-before-make)
26°
Materials & Finishes
Rotaries
Toggle:
Bushing:
Gasket:
Case Housing:
Support Bracket:
Movable Contact:
Stationary Contacts:
Terminals:
Nickel plated brass
Carbon blended polyamide; nickel plated zinc alloy for locking levers & threaded bushing
Nitrile butadiene rubber
Glass fiber reinforced polyamide
Tin plated phosphor bronze
Phosphor bronze with gold plating
Copper alloy with gold plating
Copper alloy with gold plating
Tactiles
Slides
Environmental Data
Operating Temperature Range:
Humidity:
Vibration:
Shock:
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
2
) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Tilt
Touch
Installation
Mounting Torque:
.30 ~ .45Nm (2.65 ~ 3.98 lb
in) for A1 actuator with threaded bushing only
PCB Processing
Indicators
Soldering:
Cleaning:
Wave Soldering Recommended: See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
Automated cleaning. See Cleaning specifications in Supplement section.
Accessories
Standards & Certifications
Flammability Standards:
Supplement
UL94V-0 available
The B Series toggles have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
A12
www.nkk.com
Help: How do microstrip, coplanar and stripline transmission lines work?
Dear experts, please tell me the working principle of several transmission lines such as microstrip line, coplanar line and stripline. It would be better to be more detailed. Thank you in advance....
43381557 RF/Wirelessly
【TI Select】Transimpedance Amplifier Application Guide
Good things don't come often~~:pleased: I just found an application guide for transimpedance amplifiers today, written by Mao Huaping, a high-speed application engineer at TI. TIA stands for trans-imp...
德州仪器 Analogue and Mixed Signal
Find a sensor
I need to design an online battery length measurement. Is there an optical sensor that can emit a line of light and have a receiving end at the other end? When the battery passes by, it will block par...
2008wzs Sensor
Instrumentation amplifier of ordinary op amp
In many single-chip microcomputer systems that require A/D conversion and digital acquisition, in many cases, the analog signal output by the sensor is very weak and must be amplified by a certain mul...
fighting Test/Measurement
msp430 ADC12 interrupt problem
I am making a switching power supply. I want to use the interrupt of AD12 to detect and sample at the same time. When the voltage sampled by AD12 is greater than a certain value, the P1.0 light of the...
刘123 MCU
About the keyboard driver under wince
My task is to modify the keyboard driver program in the BSP of the development board (the operating system is wince5.0) so that it can be used on a keyboard of my own design. I have studied the progra...
dlj0521 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1153  1398  2526  2321  2095  24  29  51  47  43 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号