EEWORLDEEWORLDEEWORLD

Part Number

Search

SH025M0220A5F51012

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 25V, 20% +Tol, 20% -Tol, 220uF, Through Hole Mount, RADIAL LEADED, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size62KB,3 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance  
Download Datasheet Parametric View All

SH025M0220A5F51012 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 25V, 20% +Tol, 20% -Tol, 220uF, Through Hole Mount, RADIAL LEADED, ROHS COMPLIANT

SH025M0220A5F51012 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompli
ECCN codeEAR99
capacitance220 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
leakage current0.058 mA
Manufacturer's serial numberSH
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingTR
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)25 V
ripple current250 mA
surface mountNO
Delta tangent0.16
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
Miniature Size Aluminum
Electrolytic Capacitors
SH
[ For General ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors
for the Rated Voltage up to 450V
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40° ~ +105°C / -25°~ +105°C
Working Voltage : 6.3 ~ 100V / 160 ~ 450V
Rate Capacitance Range : 0.1 ~ 15000µF / 0.1 ~ 15000µF
Capacitance Tolerance : -20 ~ +20%
DC Leakage Current (µA) : 0.01CV +3 / 0.03CV+10
( Measurements shall be made after a2 minute charge at rated working voltage at 25°C )
Dissipation Factor : at 120 Hz, 25°C
W V (V) : 6.3
10
16
25
35
50
63 ~ 100
160 ~ 250
350 ~ 450
D.F (%) : 26
22
18
16
14
12
10
15
20
For capacitor whose capacitance excceds 1000µF. The value of DF(%) is increased by 2% for every
addition of 1000µF.
W V (V)
:
6.3
4
8
10
3
6
16
2
4
25
2
3
35 ~ 100
2
3
160 ~ 250 350 ~ 450
4
8
4
8
DESCRIPTION
Long life for 2,000 hours at 105°C, ideally suited
for high quality and high reliability applications.
Feature High CV Product
Impedance : Z - 25°C / Z + 25°C
Z - 40°C / Z + 20°C
Load Life : 2000 Hours at 105°C Assured with Full Rated Maximum Ripple Current Applied
Multiplier for Ripple Current
Frequency (Hz)
6.3~100V Below~68µF
6.3~100V 100~470µF
6.3~100V 471~22000µF
160~450V ALL Cap(µF)
120
1.00
1.00
1.00
1.00
300
1.30
1.23
1.10
1.25
1K
1.57
1.34
1.13
1.40
10K~100K
2.00
1.50
1.15
1.60
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : 1000 Hours, No Voltage Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
Temperature(°C)
Factor
65
1.70
85
1.40
105
1.00
Dimensions : mm
Rubber Stand-off
4.0
Rubber End Seal
DIAGRAM OF DIMENSIONS
F
1.5
2.0
2.5
3.5
5.0
0.45
0.5
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
5.0
6.0
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F 0.5
F 0.5
0.4Max.
15Min.
0.6
L
15Min.
5Min.
D 0.5
L
5Min.
D 0.5
7.5
10.0
0.8
0.8
Will CCS change the contents of the address where the interrupt vector table is located?
Tingfengqieyin 16:48:08 May I ask, during CCS simulation, will the contents of the address where the interrupt vector table is located be modified when the program is running? Now when the program is ...
安_然 DSP and ARM Processors
How to burn the program???
I am new to AVR series microcontrollers and have a lot of questions. I am eager to know how to burn the program into ATMEGA8 (what software, hardware, etc. are needed). Thank you very much! ! [[i] Thi...
Saintif Microchip MCU
Applying timer interrupt example technology
How to use timer to realize interrupt? What are the specific operation steps? What should be paid attention to? The following is an example of using timer interrupt by an engineer: Now it is required ...
tonytong Analog electronics
【Translation】Micropy Official Tutorial 02 Running the first script
[i=s]This post was last edited by my student number on 2016-4-23 12:55[/i] [b][size=24px]2. Run the first script[/size][/b] From this tutorial, we will start running Python scripts on the pyboard. Aft...
我的学号 MicroPython Open Source section
The output of the TL062 amplifier is 12V when the input is 0V.
The same-direction amplifier is made of TL062 and powered by a single 12V power supply. When 0V is input at the input, the output is directly more than 11V. I don't know where the problem is. I hope f...
lostage0xff Analog electronics
Problems encountered in designing low frequency antennas
Hello, seniors! According to my understanding, an antenna can be equivalent to an LC oscillation circuit, and its resonant frequency is the receiving frequency of the antenna. Therefore, I use an LC c...
熊在非洲 RF/Wirelessly

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1992  2930  2867  1951  486  41  59  58  40  10 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号