EEWORLDEEWORLDEEWORLD

Part Number

Search

SK350M82B2F71825

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 350V, 20% +Tol, 20% -Tol, 82uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size61KB,3 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance  
Download Datasheet Parametric View All

SK350M82B2F71825 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 350V, 20% +Tol, 20% -Tol, 82uF, Through Hole Mount, ROHS COMPLIANT

SK350M82B2F71825 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompli
ECCN codeEAR99
capacitance82 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
leakage current0.599 mA
Manufacturer's serial numberSG
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingBULK
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)350 V
ripple current400 mA
surface mountNO
Delta tangent0.2
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
SG
[ Electronic Ballast ]
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40 ~ +105°C / -25 ~ +105°C
Working Voltage : 160 ~ 400V / 450V
Rate Capacitance Range : 4.7 ~ 330µF / 3.3~100µF
Capacitance Tolerance : -20 ~ +20%
DC Leakage Current (µA) : I = 0.02 CV + 25
( After 2 Minute Application of DC Working Voltage at 25°C )
Dissipation Factor : at 120 Hz, 25°C
WV (V) : 160
200
250
350
400
450
D.F (%) : 15
15
15
20
24
24
For capacitor whose capacitance exceeds 1000µF. The value of D.F(%) is increased by 2% for every
addition of 1000µF.
Load Life : 5000 Hours at Assured with Full Rated Maximum Ripple Current Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : Hours, No Voltage Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200 % of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
Miniature Size Aluminum
Electrolytic Capacitors
Multiplier for Ripple Current
Frequency (Hz)
6.3~100V Below~68µF
50,60
0.80
120
1.00
300
1.20
1K 10K~100K
1.40
1.6
Temperature(°C)
Factor
65
1.70
85
1.40
105
1.00
DIAGRAM OF DIMENSIONS
4.0
5.0
6.3
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F
1.5
2.0
2.5
3.5
5.0
0.5
0.5
Rubber Stand-off
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
Dimensions : mm
Rubber End Seal
F 0.5
F 0.5
0.6
L
0.4Max.
15Min.
5Min.
D 0.5
L
15Min.
5Min.
D 0.5
7.5
10.0
0.8
0.8
Using LaunchPad to drive a 4-phase 5-wire stepper motor cannot rotate accurately
[i=s]This post was last edited by bobde163 on 2014-11-30 09:55[/i] [size=4]I have been working on the stepper motor for two nights. I have also checked a lot of information and adjusted the parameters...
bobde163 Microcontroller MCU
Electronics Design Competition
The topic of this competition is smart health. I plan to make a smart medicine box. Now I can only think of the function of reminding you to take medicine at a certain time. I would like to ask my cla...
Mrasty Electronics Design Contest
Do I need to buy chip coins?
Do I need to buy more ChipCoins? I have too few ChipCoins....
weour Suggestions & Announcements
Can anyone help me look at the compilation, where is the problem, how to modify it
YES_COM: ;The current display is placed in DSP11~DSP15, and is refreshed every two milliseconds by the timer interrupt. ;Five registers need ten milliseconds to refresh once MOV A, R6; refers to the N...
pyy1980 MCU
Design of Intelligent Motor Protector Based on DSP
[i=s]This post was last edited by Aguilera on 2019-12-9 21:49[/i]Due to the emergence of production automation and various automatic control and sequential control equipment, motors are required to op...
Aguilera Microcontroller MCU
FPGA circuit problems
Why do we need to add a 100 ohm resistor to the high-speed line of FPGA? The following figure is the circuit diagram of BANK1 area....
zhihu20151126 FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 853  123  1960  2119  301  18  3  40  43  7 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号