SV200M100BZS51632 datasheet, PDF

Datasheet> All Categories > Passive components> capacitor> SV200M100BZS51632

SV200M100BZS51632: DescriptionAluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 200V, 20% +Tol, 20% -Tol, 100uF, Through Hole Mount, ROHS COMPLIANT; CategoryPassive components capacitor; File Size60KB，2 Pages; ManufacturerYAGEO; Websitehttp://www.yageo.com/; Environmental Compliance

Download Datasheet Parametric View All

SV200M100BZS51632 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 200V, 20% +Tol, 20% -Tol, 100uF, Through Hole Mount, ROHS COMPLIANT

SV200M100BZS51632 Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	YAGEO
package instruction	,
Reach Compliance Code	compli
ECCN code	EAR99
capacitance	100 µF
Capacitor type	ALUMINUM ELECTROLYTIC CAPACITOR
dielectric materials	ALUMINUM (WET)
leakage current	1.21 mA
Manufacturer's serial number	SV
Installation features	THROUGH HOLE MOUNT
negative tolerance	20%
Number of terminals	2
Maximum operating temperature	105 °C
Minimum operating temperature	-25 °C
Package shape	CYLINDRICAL PACKAGE
method of packing	BULK
polarity	POLARIZED
positive tolerance	20%
Rated (DC) voltage (URdc)	200 V
ripple current	800 mA
surface mount	NO
Delta tangent	0.15
Terminal shape	WIRE

Preview

Download Datasheet

View All

YAGEO CORPORATION

ALUMINUM ELECTROLYTIC CAPACITORS

Miniature Size Aluminum

Electrolytic Capacitors

[ For adapter and power supply applications

Series ]

105°C Single-Ended Lead Aluminum Electrolytic Capacitors For High Frequency Applications

ELECTRICAL CHARACTERISTICS

Operating Temperature : -40° ~ +105°C

Working Voltage :

160V

-25° ~ +105°C

450V

10 ~ 150µF

Rate Capacitance Range : 22 ~ 220µF

Capacitance Tolerance : -20 ~ +20%

DC Leakage Current (µA) : I = 0.06 CV + 10(µA)

whichever is greater.( After 2 minutes application of rated voltage at 25°C )

Dissipation Factor : at 120 Hz, 25°C

DESCRIPTION

Used in switching regulator applications in com-

puters. Especially for high frequency.

Low impedance and E.S.R., high permissible ripple

current at high frequency and higher operating

temperature (-40°C to +105°C).

WV (V) : 160

D.F (%) : 15

WV (V)

200

250

350

400

200

400

450

Impedance : Z - 25°C / Z + 20°C

Impedance : Z - 40°C / Z + 20°C

Load Life : After apply rated voltage with rated ripple current for 2000hrs at 105°C the capacitors

shall meet the following reuirements.

(a) Capacitance Change : Within 20% of Initial Value

(b) Dissipation Factor : Not Exceed 200% of Initial Requirement

Shelf Life : 1000 Hours, No Voltage Applied, at 105°C

(a) Capacitance Change : Within 20% of Initial Value

(b) Dissipation Factor : Not Exceed 200 % of Initial Requirement

Frequency(Hz)

120

500

10K~100K

Temperature(°C)

Factor

2.10

1.70

105

1.00

DIAGRAM OF DIMENSIONS

Rubber Stand-off

Dø

4.0

5.0

Rubber End Seal

Dimensions : mm

1.5

2.0

2.5

3.5

5.0

dø

0.45

0.5

Vinyl Sleeve

(P.V.C)

Rubber End Seal

Vinyl Sleeve

(P.V.C)

15Min.

5Min.

D 0.5

0.4Max.

15Min.

5Min.

D 0.5

6.0

8.0

10.0

12.0

13.0

16.0

18.0

22.0

F 0.5

0.6

7.5

10.0

0.8

Recommended Resources

Rapid heart rate monitor

50KHZ bandwidth amplifier circuit

ZC-2-10A automatic charger circuit

12V regulated power supply circuit using photoelectric coupling as short circuit protection

IX0689 power supply

Computer motherboard circuit diagram 440GX_34

Good news for those who want to learn PSoC4 -- Complete PSoC4 Experience: [size=4]The forum held a PS0C4 learning activity some time ago, and many original technical posts were generated during the activity. EE plans to organize these posts systematically. In the future, a ...; tiankai001 Download Centre

【ESP32-C3-DevKitM-1】+ Build the software environment for ESP32-C3 development based on the user manual: [i=s]This post was last edited by chrisrh on 2021-7-11 23:01[/i]Failed to successfully use Thonny to complete C3 related burning. First use ESP-IDF to configure, compile, and download according to the...; chrisrh Domestic Chip Exchange

I would like to ask you for advice on how to amplify the small current signal of a DIY clamp meter: I would like to ask you for advice on how to amplify the small current signal of a DIY clamp meterI am currently DIYing a clamp ammeter The target parameter is to measure current from mA to 10A The se...; deeter DIY/Open Source Hardware

How to learn ARM for students majoring in control: I will graduate soon this year. I bought an ARM9 board in my sophomore year, but I didn't use it much. The reason is that it has more applications in designing embedded systems, which made me confused...; lonerzf Programming Basics

Take a look at the photos of my smart car, absolutely stunning!: I haven't been in the lab these days. Even though Teacher Song has spoken, I went there at 4pm yesterday afternoon and started making a model car. It took me one night to assemble the model book. Alth...; qgqcheng Embedded System

Download the updated solution via SD card: Because computers are not allowed in electronic competitions, I want to make a program that can download updates by reading SD cards. I wonder if an expert can give me some advice and send me some ref...; huo_hu stm32/stm8

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components