EEWORLDEEWORLDEEWORLD

Part Number

Search

SC6M100A5F5511

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 6.3V, 20% +Tol, 20% -Tol, 100uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size66KB,3 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance  
Download Datasheet Parametric View All

SC6M100A5F5511 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 6.3V, 20% +Tol, 20% -Tol, 100uF, Through Hole Mount, ROHS COMPLIANT

SC6M100A5F5511 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance100 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
ESR580 mΩ
leakage current0.0063 mA
Manufacturer's serial numberSC
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingTAPE
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)6.3 V
ripple current210 mA
surface mountNO
Delta tangent0.15
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
Miniature Size Aluminum
Electrolytic Capacitors
SC
[ For Low Impedance and Low E.S.R
Suitable for Output of Mother Board ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors For High Frequency Applications
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40° ~ +105°C
Working Voltage : 6.3 ~ 100V
Rate Capacitance Range : 4.7 ~ 15000µF
Capacitance Tolerance : -20 ~ +20%
DESCRIPTION
Used in switching regulator applications in com-
puters. Especially for high frequency.
Low impedance and E.S.R., high permissible ripple
current at high frequency and higher operating
temperature (-40°C to +105°C).
High Temperature Load Life at 105°C for 3000
Hours
DC Leakage Current (µA) : I = 0.01 CV(µA) or 3µA Whichever is greater.
( Measurements shall be Made After a 2 Minute Charge at Rated Working Voltage )
Dissipation Factor : at 120 Hz, 25°C
WV (V) : 6.3
10
16
25
35
50
63
80
100
D.F (%) : 15
14
12
10
10
8
8
7
7
For capacitor whose capacitance exceeds 2000µF. The value of D.F(%) is increased by 2% for every
addition of 1000µF.
WV (V)
:
6.3
10
10
8
16
5
25
4
35
4
50
4
63
4
100
4
Impedance : Z - 40°C / Z + 20°C
Load Life : 3000 Hours at 105°C Assured with Full Rated Maximum Ripple Current Applied
Multiplier for Ripple Current
Frequency(Hz)
~4.7µF
5.6~33µF
34~330µF
331~1000µF
1200µF Higher
50
0.30
0.40
0.60
0.65
0.85
120
0.40
0.50
0.70
0.80
0.90
300
0.50
0.60
0.80
0.90
0.95
1K
0.70
0.80
0.90
0.98
0.98
10K 100K
0.80 1.00
0.90 1.00
0.95 1.00
1.00 1.00
1.00 1.00
5 x 11 ~ 10 x 12 : Life = 2000 Hours
10 x 15 or Higher : Life = 3000 Hours
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : 1000 Hours, No Voltage Applied, at 105°C
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200 % of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
Temperature(°C)
Factor
65
1.80
85
1.50
105
1.00
Dimensions : mm
Rubber Stand-off
4.0
Rubber End Seal
DIAGRAM OF DIMENSIONS
F
1.5
2.0
2.5
3.5
5.0
0.45
0.5
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
5.0
6.3
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F 0.5
F 0.5
0.4Max.
15Min.
0.6
L
15Min.
5Min.
D 0.5
L
5Min.
D 0.5
7.5
10.0
0.8
0.8
[GD32E231 DIY Contest] 1. Unpacking the product
Yesterday I finally received the long-awaited board [GD32E231]. It includes a development board, 2 chips, and a data cable, but there is no pin header, which is a bit bad. I need to solder the pin hea...
hehung GD32 MCU
#August modification# Add an external antenna to the Tmall Magic Box to enhance the signal
[size=3][color=#333333][backcolor=rgb(252, 253, 254)]There are three versions of Tmall Magic Box. The antennas of version A and C are relatively easier to modify than version E. I tried to modify the ...
liuxing4585 DIY/Open Source Hardware
Filtering
I designed a 300 Hz high pass filter, but when I input a 10 Hz sine wave, I still get a good sine wave. What am I doing wrong?...
果啸 Analog electronics
How to deal with the "ground" of the front and back parts of such a circuit?
bq24070+bq27200...
蓝雨夜 Analogue and Mixed Signal
Can anyone help analyze the source code of UC/SERIAL?
The attachment is the UC/SERIAL source code of Fujitsu's FM3 downloaded from the official website. Can anyone help analyze the source code?There are a few files related to the chip. I mainly want to u...
andylxp198486 Real-time operating system RTOS
Analyzing the clock problem of MSP430
After the microcontroller is powered on, if the clock system is not set, the default 800 kHz DCOCLK is used as the clock source of MCLK and SMCLK, and LFXT1 is connected to a 32768 Hz crystal and work...
fish001 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1229  2701  1974  1908  1470  25  55  40  39  30 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号