EEWORLDEEWORLDEEWORLD

Part Number

Search

307E-114-2007

Description
Board Connector, 14 Contact(s), 1 Row(s), Male, Straight, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle
CategoryThe connector    The connector   
File Size153KB,1 Pages
ManufacturerMethode Electronics Inc.
Download Datasheet Parametric View All

307E-114-2007 Overview

Board Connector, 14 Contact(s), 1 Row(s), Male, Straight, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle

307E-114-2007 Parametric

Parameter NameAttribute value
MakerMethode Electronics Inc.
Reach Compliance Codeunknow
ECCN codeEAR99
Other featuresWITH HOOKS
Board mount optionsPCB EDGE LOCKING HOOK
subject depth0.45 inch
body length2.178 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationSN-PB ON NI
Contact completed and terminatedTIN/LEAD OVER NICKEL
Contact point genderFEMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact resistance5 mΩ
Contact styleSQ PIN-SKT
DIN complianceNO
Dielectric withstand voltage1500VAC V
Filter functionNO
IEC complianceNO
maximum insertion force8.896 N
Insulation resistance500000000000 Ω
Insulator colorNATURAL
insulator materialGLASS FILLED POLYESTER
MIL complianceNO
Plug contact pitch0.156 inch
Plug informationMULTIPLE MATING PARTS AVAILABLE
Mixed contactsNO
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
OptionsGENERAL PURPOSE
PCB contact patternRECTANGULAR
polarization keyPOLARIZED HOUSING
Rated current (signal)7 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.165 inch
Terminal pitch3.96 mm
Termination typeSOLDER
Total number of contacts14
UL Flammability Code94V-0
Evacuation force-minimum value.556 N
.156” (3.96mm)
Through Hole Vertical Mount Connector
3000 SERIES “TERMACON”
PART NUMBER LEGEND
30XX-XXX-XXXX
CONTACT TAIL DIMS (SEE TABLE 2)
CONTACT MATERIAL (SEE NOTE 1)
OPTIONS
2 - HIGH INSERTION FORCE CONTACT
3 - LOW INSERTION FORCE CONTACT
NO. OF POSITONS (SEE TABLE 1)
OPTIONS
0-
1-
3-
6-
7-
8-
WITH LEGS
WITH HOOKS
WITH HOOKS AND LOCKING RAMP
WITH LOCKING RAMP
WITH HOOKS, LOCKING RAMP AND POLARIZING KEY
WITHOUT HOOKS, W/ LOCKING RAMP AND POLARIZING KEY
CONTACT FINISH (SEE NOTE 2)
INSULATOR MATERIAL (SEE NOTE 1)
MATING HEADERS: 3100 SERIES
HOLE
LEG
LOCKING
RAMP
POLARIZING KEY &
LOCKING RAMP
Connector Products
1700 Hicks Road • Rolling Meadows, IL 60008 USA
Telephone: 847.392.3500 • Fax: 847.392.9404
email: mcpsales@methode.com • Web Page: www.methode.com
Introduction to ARM assembly pseudo-instructions (2)
Assembly Control Pseudo-Instructions Assembly control pseudo-instructions are used to control the execution flow of the assembly program. Commonly used assembly control pseudo-instructions include the...
呱呱 ARM Technology
The software used to download the stc isp is not able to handshake with the computer
As the title says, at first I suspected that the communication line was not connected properly, but after changing the line, the problem still exists and the handshake protocol cannot be performed. Do...
yanghui_45 Embedded System
The high power tube of the switching power supply is broken
As shown in the figure, the switching power supply made of DPA425 has an output voltage of 28V (regulated) and 50V when no-load. When the regulated voltage is connected to a load of 500Ω, the voltage ...
chilezhima Power technology
Can someone please give me some pointers on the procedure flow of the Stellaris LwIP routine?
As the title says, for example, if a data is sent from the host computer, how does the program handle it? It seems that the routine uses systick interrupt and Ethernet hardware interrupt to handle it,...
186874509 Microcontroller MCU
v-HDL Design Research
[size=9pt]I. Portable Coding 1. Use only IEEE standard types (VHDL): (1) Use STD_LOGIC type instead of STD_ULOGIC type; (2) Do not create too many subtypes in the design; (3) Do not use BIT and BIT_VE...
songbo FPGA/CPLD
How to disassemble an integrated circuit
[size=4]When repairing circuits, it is often necessary to remove integrated circuits from printed circuit boards. Since integrated circuits have many and dense pins, it is difficult to remove them, an...
songbo Creative Market

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1937  961  2740  2894  947  40  20  56  59  44 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号