EEWORLDEEWORLDEEWORLD

Part Number

Search

TM250-.0162OHM-0.5%

Description
Fixed Resistor, Wire Wound, 250W, 0.0162ohm, 0.5% +/-Tol, -90,90ppm/Cel,
CategoryPassive components    The resistor   
File Size58KB,1 Pages
ManufacturerElectro Technik Industries
Environmental Compliance
Download Datasheet Parametric View All

TM250-.0162OHM-0.5% Overview

Fixed Resistor, Wire Wound, 250W, 0.0162ohm, 0.5% +/-Tol, -90,90ppm/Cel,

TM250-.0162OHM-0.5% Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerElectro Technik Industries
Reach Compliance Codeunknow
ECCN codeEAR99
structureAluminum Housing
Maximum operating temperature275 °C
Minimum operating temperature-55 °C
Package height55.5 mm
Package length114.3 mm
Package formChassis Mou
Package width76.2 mm
Rated power dissipation(P)250 W
resistance0.0162 Ω
Resistor typeFIXED RESISTOR
seriesTM
technologyWIRE WOUND
Temperature Coefficient-90,90 ppm/°C
Tolerance0.5%

TM250-.0162OHM-0.5% Preview

TEPRO
ELECTRO TECHNIK
TYPE “TM”
PRECISION POWER WIREWOUND
ALUMINUM HOUSED,
CHASSIS MOUNT RESISTORS
FEATURES:
Chassis mount for heat sink effect
Epoxy protected windings
Miniature size
Noninductive windings
High stability
Optimum power to size ratio
Higher ambients
Withstand severe environments
VARIATIONS:
Special TC on request
Closer tolerances to .01%
Special terminals
Flexible leads
ENVIRONMENTAL SPECIFICATIONS:
GENERAL
SPECIFICATIONS:
Standard tolerances:
±0.1 to 5%
Dielectric strength:
1000 VAC TM-5, TM-10, TM-25
2000 VAC TM-50,
3000 VAC TM-100, TM-250
Insulation resistance:
10000 megohms minimum
Temperature coefficients:
10Ω and above: ±20ppm
1Ω to 9.9Ω: ±50ppm
Below 1Ω: ±90ppm
Terminal strength:
5lb. pull test TM-5, TM-10
10lb. pull test all others
Standard terminals:
Tinned copper, flattened and
pierced TM-5 to TM-50
Threaded on TM-100 and TM-250
Housing: Anodized aluminum
Core:
Steatite or alumina
Winding: Copper-nickel or nickel-chrome
alloy as required by resistance
Sealant: High-temperature silicone
Power rating: Based on;
(a) full power operation at 25°C
(b) 1% maximum
R in
1000 hour load life
(c) maximum hotspot 275°C
(d) mounting on proper heat sink
Recommended heat sink:
Aluminum chassis;
6 x 4 x 2 x .040 TM-5, TM-10
7 x 5 x 2 x .040 TM-25
12 x 12 x .050 TM-50
12 x 12 x .125 TM-100, TM-250
TEST
Load life
Moisture resistance
Resistance temperature
Characteristic
Thermal shock
Momentary overload
Dielectric
High temperature storage
Shock
Vibration
Terminal strength
MIL-R-18546
± (1% + 0.05Ω)
R
± (1% + 0.05Ω)
R
±50ppm to 2000Ω
±30ppm over 2000Ω
± (.5% + 0.05Ω)
R
± (.5% + 0.05Ω)
R
± (.2% + 0.05Ω)
R
± (.5% + 0.05Ω)
R
± (.2% + 0.05Ω)
R
± (.2% + 0.05Ω)
R
± (.2% + 0.05Ω)
R
POWER
TEPRO RATINGS/WATTS
TYPE TEPRO
MIL.
TM 5
TM 10
TM 25
TM 50
TM 100
TM 250
7.5
12.5
25.0
50.0
100.0
250.0
5
10
20
30
75
120
RESISTANCE RANGE OHMS
TEPRO
TYPE
MIN.
MAX.
0.005
0.005
0.005
0.005
0.010
0.010
20K
40K
90K
250K
500K
700K
Notes:
For noninductive windings
add "NI" to type. Maximum
resistance 1/3 that shown.
All data and dimensions
subject to change without
notice.
DERATING:
% OF RATED POWER
Operation in high ambients or on reduced
chassis areas requires derating in accordance
with the accompanying curve. TM-5 and
TM-10 types may be operated in ambients
to 75°C without derating. (Curve A)
DERATING CURVE
120
100
80
60
40
20
0
25
A
B
75
125
175
225 275
AMBIENT TEMP. °C
Curve A: TM-5, TM-10
Curve B: All others
325
Toll Free: 800.346.5164
Phone:
727.796.1044
11
TEPRO
P.O. BOX 1260 • CLEARWATER, FL 33757
ELECTRO TECHNIK
There seems to be a problem with the STM32_IAP routine
I would like to ask the moderator for advice. When I used the "STM32F10x_IAP_V3.1.0" routine provided by the st website, I found that when I used 232 to download the program, IAP was normal, but when ...
rock_17 stm32/stm8
Why does Unico prompt that STEVAL-MKI197V1 is not supported? --- Solved
[i=s]This post was last edited by a media student on 2020-4-12 22:31[/i]I got the board today and downloaded the unico software, but it prompted the following error:Please give me some pointers..Thank...
传媒学子 ST MEMS Sensor Creative Design Competition
Design of automotive electronic control system unit based on ARM
With the widespread application of electronic control units (ECUs) in automobiles, the degree of automobile electrification is getting higher and higher. Although the increase of electronic control sy...
frozenviolet Automotive Electronics
USB download based on AT91SAM9G45 development board
Use SAM-BA 1.13 AT91-ISP.exe (Windows XP - v1.13 current release) for USB download. After installing the software, the [font=Verdana]sam-ba v2.9[/font] icon will appear on the desktop. First power on ...
ye0217 Embedded System
The process of WEBENCH design + STC15F2K60S2 core control board power supply design based on TPS54360 chip design
[i=s] This post was last edited by fengye5340 on 2014-7-2 15:17 [/i] [align=left][b][font=宋体][size=5]1. Solution Introduction: [/size][/font][/b] [/align][align=left] [size=4] [font=宋体] In industrial ...
fengye5340 Analogue and Mixed Signal
Ask the experts about the receiving problem of mt8888
[color=#FF0000] Please tell me about the receiving problem of mt8888[/color] The following is my program: I can send, but the reception is interrupted, but I can’t read the number. I always read the s...
yhb123 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 124  2475  67  2302  668  3  50  2  47  14 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号